2022-12-20

Ledningsnett – hoved foran – aktivt panser (fjerne og skifte ut)

Korrigeringskode 171034023.06 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Denne prosedyren er et UTKAST. Selv om den har blitt godkjent, kan det hende at advarsler og forholdsregler mangler. Følg sikkerhetskravene, og vær ytterst forsiktig ved arbeid på eller nær høyspenningssystemer og -komponenter. Send korrigeringer og tilbakemeldinger til ServiceDevelopment@teslamotors.com.

Fjerne

  1. Open the front LH and front RH doors.
  2. Open the hood.
  3. Place wheel chocks on both rear wheels.
  4. Put vehicle in Neutral.
  5. Disconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  6. Disconnect first responder loop.
  7. Remove the LH lower A-pillar trim. See Deksel – A-stolpe – nedre – venstre (fjerne og skifte ut).
  8. Release the clips that attach the footrest.
  9. Remove the RH knee airbag. See Kollisjonspute – kne – fører (fjerne og skifte ut).
  10. Remove the main instrument panel decor. See Dekorkledning – instrumentpanel – hoved (fjerne og skifte ut).
  11. Remove the glove box. See Hanskerom – med knekollisjonsputer (uten varmepumpe) (fjerne og skifte ut).
  12. Remove the RH footwell duct. See Kanal – fotbrønn – høyre (venstrestyrt) (fjerne og skifte ut).
  13. Remove the RH air wave duct. See Kanal – luftbølge – høyre (venstrestyrt) (fjerne og skifte ut).
  14. Remove the underhood storage unit. See Oppbevaringsrom under panser (fjerne og skifte ut).
  15. Remove the 12V auxiliary battery. See12 V-/lavspenningsbatteri (fjerne og skifte ut).
  16. Remove the nut that attaches the 12V battery rear hook tie down.
  17. Remove the wiper motor assembly. See Spylermodul (fjerne og skifte ut).
  18. Remove the bolt that attaches the thermal harness cover to the front body controller module, and then remove the cover from the module.
  19. Disconnect the thermal harness from the front body controller module connector.
  20. Remove the bolts that attach the front body controller module cover to the front body controller module, and then remove the cover.
  21. Disconnect the main front harness from the front body controller module connectors.
  22. Remove the ground bolt from 12V negative terminal.
  23. Remove 12v negative harness clip from front controller.
  24. Remove upper ground strap from the vehicle body.
  25. Remove the bolts that attach the front body controller module to the body.
  26. Remove bolts securing front controller.
  27. Release harness guide and remove the front controller from vehicle.
  28. Remove fresh air intake assembly.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x studs, Remove from bulkhead studs.
  29. Remove and discard nuts securing car computer to the bulkhead.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x nyloc nuts, 13mm, 7.1 Nm.
  30. Remove power cable from right body controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, release locking tab.
  31. Disconnect 12V connector from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  32. Release the clip that attaches the inline electrical harness connector to the RH body controller module, and then disconnect the electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, 1x clip.
  33. Disconnect frunk connector from right controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, J8.
  34. Slide car computer inward to allow access to connectors and harness clips.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Be careful not to strain harness and connectors.
  35. Remove the front harness clips from car computer.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  36. Disconnect the LH front harness connector from car computer.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  37. Disconnect the RH front harness connectors from car computer.
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x connectors.
  38. Push the RH side of the front harness through the bulkhead.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips.
  39. Disconnect harness connector for windshield heater from underhood area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  40. Secure the windshield harness out of the way to avoid damage.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Secure using tape.
  41. Remove the front end harness windshield connector from the body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  42. Release clips securing harness behind RH shock tower.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  43. Remove front harness clip from washer tank.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  44. Disconnect front harness connectors from brake booster area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors, Brake fluid level sensor, Brake booster.
  45. Disconnect brake booster lower connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  46. Disconnect the hydraulic control unit connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Disengage locking tab and pull up on connector to release.
  47. Remove front harness clips around LH front frame rail area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x clips.
  48. Remove the front harness ground terminals at LH front shock tower.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x bolts, 10mm, 8 Nm,Inspect bolts: if they are self tapping tri-lobular bolts (1128269-00-A) then discard, If they are normal bolts (1447438-00-A) they can be reused.
  49. Disconnect LH front headlamp connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  50. Disconnect the steering gear assembly connectors.
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x connectors, Two stage connectors, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector.
  51. Remove AC compressor ground strap.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, T25, 7 Nm.
  52. Remove horse clips from steering gear harness bracket.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  53. Remove steering gear harness bracke clip and remove from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  54. Disconnect the FDU logic connector at the LH frame rail.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, 2 stage connector, Release the grey locking tab then press on the tab to release the connector.
  55. Disconnect RH headlamp connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector.
  56. Remove the front harness ground terminals at RH front shock tower.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 8 Nm,1x connector,Inspect bolts: if they are self tapping tri-lobular bolts (1128269-00-A) then discard, If they are normal bolts (1447438-00-A) they can be reused.
  57. Remove the front harness clip around RH front frame rail area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x clips.
  58. Remove the wheel chocks.
  59. With an assistant, move the vehicle to a lift.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    The vehicle is safely pushed for only a very short distance and at a very slow speed.
  60. Remove the front LH and front RH wheels. See Hjulenhet (fjerne og skifte ut).
  61. Remove the front LH and front RH arch liners. See Innerskjerm – foran – venstre (fjerne og skifte ut).
  62. Remove lower bolt securing washer tank to vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 3 Nm.
  63. Loosen forward bolts securing LH corner of front fascia to fender.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 10mm, 4 Nm.
  64. Remove bolt securing LH corner of fascia to fender.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 3 Nm.
  65. Disconnect the front harness connector for the LH front carrier harness.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector.
  66. Disconnect the front harness from the LH acceleration sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector.
  67. Remove the front harness clips from the outer LH rail area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  68. Disconnect the front harness from CFM.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  69. Disconnect the LH front wheel speed sensor and body height sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  70. Remove the front harness clips around LH front wheel liner area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x clips, North American region vehicles have 2x clips.
  71. Remove the front harness clip for the LH side repeater and camera harness.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  72. Disconnect the front harness connectors for the LH side repeater and camera.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  73. Disconnect pyrotechnic actuator connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector, release the locking by sliding it away from the connector.
  74. Loosen forward bolts securing RH front corner of front fascia to fender.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 10mm, 4 Nm.
  75. Remove bolt securing RH front corner of front fascia to fender.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 3 Nm.
  76. Disconnect 12V harness for front fascia.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector, Release the locking tab by sliding it away from the connector, Then depress the grey lock to release the connector.
  77. Remove the clip securing harness to pedestrian warning speaker assembly.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  78. Disconnect pedestrian warning speaker.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Release the locking tab by sliding it away from the connector, then depress the grey locking tab to release.
  79. Remove front harness clip from the RH front fascia mounting bracket.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  80. Disconnect front harness from front end module harness.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector.
  81. Disconnect the front harness from the RH acceleration sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector.
  82. Remove the front harness clips from the outer RH rail area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  83. Disconnect the RH front wheel speed sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  84. Remove the front harness clips around front of RH front wheel liner for the wheel speed sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  85. Remove the front harness clip at the rear of RH front wheel liner area for the side repeater and camera harness.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  86. Disconnect the front harness connectors for the RH side repeater and camera.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  87. Disconnect RH pyrotechnic actuator connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector, release the locking by sliding it away from the connector.
  88. Raise vehicle fully and lower lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Verify doors are clear of surrounding objects.
  89. Remove the front aero shield. See Panel – luftskjerm – foran (fjerne og skifte ut)
  90. Remove push clips securing lower valance to front sway bar brackets.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x push clips, the number of clips on newer vehicles may vary.
  91. Remove LH harness bracket clip and remove from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  92. Lower the vehicle.
  93. Release front fascia, see Støtfanger – foran (fjerne og skifte ut) .
  94. Disconnect the low and high tone horn connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  95. Disconnect LH front ped pro pressure tube sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector.
  96. Disconnect RH front ped pro pressure tube sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector.
  97. Remove upper bolt securing washer tank to vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 3 Nm.
  98. Disconnect washer pump and level sensor connectors.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  99. Remove washer tank from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors, keep washer tank upright to keep contents from spilling.
  100. Remove the front harness clips from the body under the washer tank area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips.
  101. Remove thermal sub-harness clip from front harness bracke and moved to the side.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  102. Remove AC Compressor harness clip from front harness bracket.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  103. Remove bolt securing front harness bracket from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts,10mm,9 Nm.
  104. Route the LH side of the electrical harness from the wheel liner, through the underhood storage unit area, and to the front body controller module area.
  105. Route the RH side of the electrical harness from the wheel liner, through the underhood storage unit area, and to the front body controller module area.
  106. Remove the electrical harness from vehicle.

Montere

  1. Position the front harness to vehicle for installation.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Make sure to route RH branch underneath A/C compressor HV harness.
  2. Route the front harness around the brake booster area and push the LH side of the harness into driver side compartment.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips, make sure to install grommet in proper orientation.
  3. Route the front harness around the HVAC plenum duct area and push the RH side of the harness into passenger side compartment.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips, Route harness underneath A/C HV harness, Make sure to install grommet in proper orientation.
  4. Route the RH side of the front harness toward the RH side of the front fascia area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Make sure plastic housing is properly oriented with clips facing frame rail, Feed harness down behind fascia.
  5. Route the RH side of the front harness from frunk to RH wheel liner area.
  6. Route the LH side of the front harness toward the LH side front fascia area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Make sure plastic housing is properly oriented with clips facing frame rail, Feed harness down behind fascia.
  7. Route the LH side of the front harness from frunk to LH wheel liner area.
  8. Install front harness clips under the washer tank area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips.
  9. Connect the hydraulic control unit connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Gently push connector downward, Engage locking tab.
  10. Connect brake booster lower connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  11. Connect washer pump and level sensor connectors.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  12. Install washer tank into position.
  13. Install upper bolt securing washer tank to vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 3 Nm.
  14. Connect harness near brake booster area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors, engage locking tabs.
  15. Install front harness clips around LH front frame rail area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x clips.
  16. Install the front harness ground terminals to LH front shock tower.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x bolts, 10mm, 8 Nm, install new bolt if original was a self tapping tri-lobular bolt, New bolt (1447438-00-A) can be reused.
  17. Connect the front harness connector to LH headlamp.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  18. Connect the steering gear assembly connectors.
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x connectors, Engage locking tabs.
  19. Install AC compressor ground strap.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, T25, 7 Nm.
  20. Connect the FDU logic connector at the LH frame rail.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Engage locking tab.
  21. Connect the front harness to RH headlamp.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, engage locking tab.
  22. Install the front harness clip around RH front frame rail area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x clips.
  23. Install the front harness ground terminals to RH front shock tower.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 10mm, 8 Nm,install new bolt if original was a self tapping tri-lobular bolt, New bolt (1447438-00-A) can be reused.
  24. Secure harness clips behind RH shock tower.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  25. Install the windshield harness heater connector to the body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  26. Removed the tape from the windshield heater harness and windshield.
  27. Connect the windshield heater harness.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  28. Install harness guide and tilt backward for installation.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x tab.
  29. Install bolts securing front controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x bolts, 10mm, 10 Nm.
  30. Install front controller harness connectors.
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x connectors, 1x harness guide.
  31. Install front controller upper ground strap to body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 10 Nm.
  32. Install the ground bolt to 12V negative terminal.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 6 Nm.
  33. Install 12V negative harness clip to VC front.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x edge clip.
  34. Install front controller shield to the front controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 10mm, 8.5 Nm.
  35. Connect thermal sub-harness to front controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, rotate fully to secure locking tab.
  36. Install bolt securing front harness bracke from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts,10mm,9 Nm.
  37. Install AC Compressor harness clip to front harness bracket.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  38. Connect LH front ped pro pressure tube sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Engage locking tab.
  39. Connect RH front ped pro pressure tube sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, engage locking tab.
  40. Connect the low and high tone horn connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  41. Install the front fascia. See Støtfanger – foran (fjerne og skifte ut).
  42. Raise vehicle fully and lower lift onto locks.
  43. Install LH harness bracke clip to vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  44. Install push clips securing lower valance to front sway bar brackets.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x push clips, the number of clips on newer vehicles may vary.
  45. Install the aero shield. See Panel – luftskjerm – foran (fjerne og skifte ut).
  46. Lower vehicle partially and set onto locks.
  47. Install lower bolt securing washer tank to vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 3 Nm.
  48. Connect the front harness connectors for the LH side repeater and camera.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  49. Connect pyrotechnic actuator connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector, Engage locking tab.
  50. Install the front harness clip around rear of LH front wheel liner area for the side repeater and camera.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  51. Install the front harness clips around front of LH front wheel liner area for the wheel speed sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x clips, vehicles not equipped with ride-height sensor have 2x clips.
  52. Connect the LH front wheel speed sensor and body height sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  53. Install the harness clips at outer side of LH rail.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  54. Connect LH acceleration sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  55. Connect the front harness connector for the LH front end module harness.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector.
  56. Connect the front harness to the CFM.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  57. Connect the front harness connectors for the RH side repeater and the camera.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors.
  58. Connect RH pyrotechnic actuator connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector, Engage locking tab.
  59. Install the front harness clip around rear of RH front wheel liner area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  60. Install the front harness clips around front of RH front wheel liner area.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  61. Connect the RH front wheel speed sensor harness connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  62. Install the harness clips at outer side of RH rail.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  63. Connect RH front acceleration sensor.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector.
  64. Connect the front harness connector for the RH front carrier harness.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x locking connector, engage locking tab.
  65. Install front harness clip to the RH front fascia mounting bracket.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  66. Connect 12V harness for front fascia.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Engage the locking tab.
  67. Connect pedestrian speaker.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Engage locking tab.
  68. Secure harness to pedestrian warning speaker.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  69. Install the RH and LH front wheel arch liner. See Innerskjerm – foran – venstre (fjerne og skifte ut).
  70. Install the RH and LH front wheel. See Ratt (fjerne og skifte ut).
  71. Lower vehicle until tires are touching the ground.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
  72. Install the RH and LH front wheel center cap. See Kapsel – hjul (fjerne og skifte ut).
  73. Remove lift arms from below vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Lower lift arms fully and remove from under vehicle as necessary.
  74. Push vehicle away from lift.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Recommend assistance, Note this vehicle can only be safely pushed for a very short distance and at very slow speed, Chock wheels.
  75. Secure front harness clip to washer tank.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip.
  76. Connect frunk connector to left body controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, J8.
  77. Connect front harness white connector to LH body harness and clip to LH body controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, 1x clip.
  78. Connect power cable from left body controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, release locking tab.
  79. Install the front passenger knee airbag. See Kollisjonspute – kne – passasjersete foran (fjerne og skifte ut)
  80. Install screw and clips securing LH footwell cover.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x push clips, 1x screw, T20, 2.5 Nm.
  81. Connect the front harness connectors to RH side of car computer.
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x connectors.
  82. Connect the front harness connector to LH side of car computer.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector.
  83. Install the front harness to car computer clips.
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips.
  84. Slide car computer into position on bulkhead.
  85. Connect front harness connector to right body controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, J8.
  86. Connect black connector and secure to right body controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, 1x clip.
  87. Connect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  88. Install power cable to right body controller.
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Secure locking tab.
  89. Install the RH air wave duct. See Kanal – luftbølge – høyre (venstrestyrt) (fjerne og skifte ut).
  90. Install the RH footwell duct. See Kanal – fotbrønn – høyre (venstrestyrt) (fjerne og skifte ut).
  91. Install the glove box. See Hanskerom – med knekollisjonsputer (uten varmepumpe) (fjerne og skifte ut).
  92. Install clips securing RH footwell assembly.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x push clips.
  93. Install the RH lower A-pillar trim. See Deksel – A-stolpe – nedre – venstre (fjerne og skifte ut).
  94. Install the main instrument panel decor. See Dekorkledning – instrumentpanel – hoved (fjerne og skifte ut).
  95. Install nuts securing car computer to the bulkhead.
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x nyloc nuts, 13mm, 7.1 Nm, Install new nyloc nuts.
  96. Install fresh air intake assembly.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set clips on bulkhead studs.
  97. Install the wiper motor assembly. See Spylermodul (fjerne og skifte ut).
  98. Install the 12V auxiliary battery. See12 V-/lavspenningsbatteri (fjerne og skifte ut).
  99. Install the underhood storage unit. See Oppbevaringsrom under panser (fjerne og skifte ut).
  100. Close hood.
  101. Close the front LH and front RH doors.