2025-03-10

Modul – karosserikontroll – venstre (venstrestyrt) (varmepumpe) (fjerne og skifte ut)

Korrigeringskode 17152112 0.48 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

  • 2023-11-13: Fixed error in routine.

Fjerne

  1. Open all doors and lower all windows.
  2. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  3. Move the driver seat fully rearward.
  4. Disconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  5. Remove the LH instrument panel end cap. See Deksel – instrumentpanel – venstre (fjerne og skifte ut).
  6. Remove the LH middle A-pillar trim. See Kledning – A-stolpe – midten – venstre (fjerne og skifte ut).
  7. Remove the LH lower A-pillar trim. See Deksel – A-stolpe – nedre – venstre (fjerne og skifte ut).
  8. Remove the driver footwell cover. See Deksel – fotbrønn – fører (fjerne og skifte ut).
  9. Remove the driver knee airbag. See Kollisjonspute – kne – fører (fjerne og skifte ut).
  10. Remove the LH footwell duct. See Kanal – fotbrønn – venstre (venstrestyrt) (fjerne og skifte ut).
  11. Release the connector lock, and then disconnect the J7 LH front door electrical connector from the LH body controller module.
  12. Release the connector lock, and then disconnect the J9 LH front seat electrical connector from the LH body controller module.
  13. Release the connector lock, and then disconnect the J10 instrument panel electrical connector from the LH body controller module.
  14. Disconnect the J11 HVAC electrical connector from the LH body controller module.
  15. Disconnect the inline electrical harness connector X909 from the LH body harness, and then separate it from the LH body controller module.
  16. Release the connector lock, and then disconnect the J1 power connector from the LH body controller module.
  17. Disconnect the J6 front underhood storage connector from the LH body controller module.
  18. Disconnect the J5 body 3 electrical connector from the LH body controller module.
  19. Release the connector lock, and then disconnect the J4 body 2 connector from the LH body controller module.
  20. Disconnect the J2 body 1 electrical connector from the LH body controller module.
  21. Release the electrical harness clips that attach the LH body controller module to the vehicle.
  22. Move the LH body harness away from the LH body controller module.
  23. Remove and discard the nut that attaches the LH body controller module to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 10 mm 12 pkt. pipenøkkelinnsats
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
    • 2 i forlengelse
  24. Slide the LH body controller upwards to release the W-clip, and then move the LH body controller module out from underneath the instrument panel.
  25. Remove the LH body controller module from the vehicle.

Montere

  1. Maneuver the LH body controller module into position under the IP carrier. Align the W-clip with the body cutout, and then slide down to attach the LH body controller module to the body.
  2. Install a new nut that attaches the LH body controller module onto the body.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 10 mm 12 pkt. pipenøkkelinnsats
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
    • 2 i forlengelse
  3. Move the LH body harness towards the left side of the LH body controller module, and then attach the harness clips to the LH body controller module.
  4. Connect the J2 body 1 electrical connector to the LH body controller module , and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the electrical connector is fully seated.
  5. Connect the J4 body 2 electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the electrical connector is fully seated.
  6. Connect the J5 body 3 electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the electrical connector is fully seated.
  7. Connect the J6 front underhood storage unit connector to the LH body controller module.
  8. Connect the J1 power connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the electrical connector is fully seated.
  9. Connect the inline electrical connector X909 to the LH body harness, and then clip it to the LH body controller module.
  10. Connect the J11 HVAC electrical connector to the LH body controller module.
  11. Install the J10 instrument panel electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the electrical connector is fully seated.
  12. Connect the J9 LH front seat electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the electrical connector is fully seated.
  13. Connect the J7 LH front door electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the electrical connector is fully seated.
  14. Install the LH footwell duct. See Kanal – fotbrønn – venstre (venstrestyrt) (fjerne og skifte ut).
  15. Install the driver knee airbag. See Kollisjonspute – kne – fører (fjerne og skifte ut).
  16. Install the driver footwell cover. See Deksel – fotbrønn – fører (fjerne og skifte ut).
  17. Install the LH lower A-pillar trim. See Deksel – A-stolpe – nedre – venstre (fjerne og skifte ut).
  18. Install the LH middle A-pillar trim. See Kledning – A-stolpe – midten – venstre (fjerne og skifte ut).
  19. Install the LH instrument panel end cap. See Deksel – instrumentpanel – venstre (fjerne og skifte ut).
  20. Connect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Do not power on the climate control system until this procedure has been fully completed.
  21. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  22. Perform a service CAN redeploy. See Installer programvare på nytt – Toolbox.
  23. Sit in the front passenger seat and close the RH front door.
  24. Utfør følgende rutine med Servicemodus eller Toolbox (se 0005 – Servicemodi):
  25. Move the front passenger seat to the original position.
  26. Raise the RH front window and close the RH front door.
  27. Move the driver seat to the original position.
  28. Close the LH front door.
  29. Inform the customer that their liftgate opening height settings have been reset and to refer to the owner's manual for instructions on setting the liftgate opening height.