2024-09-16

Modul – Restraint Control (varmepumpe) (fjerne og skifte ut)

Korrigeringskode 20015012 0.36 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

  • 2024-05-14: Replaced Toolbox 3 routines by routines using the touchscreen.
  • 2024-04-18: Eliminated redundant ODIN routine and refined instructions on headlight adjustment.
  • 2023-10-20: Added step to aim the headlights.
  • 2023-09-26: Updated links to Center Console 2.0 (Remove and Install).
  • 2023-08-24: Added additional warning to make sure LV is disconnected.
  • 2023-09-05: Updated the Toolbox routine steps.
Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Videoen(e) som er inkludert i denne prosedyren er ment som en oversikt kun som et tillegg. Følg alle trinnene som er oppført i prosedyren, for å unngå skade på komponenter og/eller personskade.
Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Forsikre deg om at 12 V-/lavspenningsstrøm har vært frakoblet i minst ett minutt før du kobler det elektriske ledningsnettet fra komponentene til det ekstra sikringssystemet (SRS), slik som Restraint Control Module, sensorer, kollisjonsputer osv. Hvis det ikke gjøres, kan sikkerhetssystemet oppføre seg utilsiktet. Se Forholdsregler for kollisjonsputer og Supplementary Restraint System (SRS) for mer informasjon om SRS-forholdsregler.
Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Komponentene til det ekstra sikringssystemet (SRS) kan være farlige hvis de ikke håndteres riktig. Se Forholdsregler for kollisjonsputer og Supplementary Restraint System (SRS) for mer informasjon om SRS-forholdsregler.
Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Det er viktig å koble fra 12 V-/lavspenningsstrøm mens du utfører reparasjoner relatert til det ekstra sikringssystemet (SRS). Hvis bilens 12 V-/lavspenningsstrøm IKKE er koblet fra og Restraint Control Module fjernes eller forstyrres, kan dette føre til at bilens kollisjonsputer utløses.

Fjerne

  1. Open all the doors and lower the windows.
    Informational PurposesAn informational icon, calling your attention
    Merk
    If the vehicle is being powered down, latch the rear doors to prevent accidental closure.
  2. Put the vehicle in Service Mode. See Servicemodus.
  3. Open the hood.
  4. Remove the center console assembly from the vehicle. See Midtkonsoll (2.0) (fjerne og montere).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Sikre at lavspenningen er frakoblet før du fortsetter til neste trinn.
  5. Release the locking tabs, release the connector levers, and disconnect the restraint control module connectors (x2).
  6. Remove and discard the nuts (x3) that attach the restraint control module to the vehicle, and then remove the module from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel

Montere

  1. Position the restraint control module into vehicle, and then install new nuts (x3) that attach the module to the vehicle.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Merk
    Verify that the part number on the new module is correct.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  2. Connect the restraint control module connectors (x2), and then engage the locking levers and connector locks.
  3. Install the center console assembly into the vehicle. See Midtkonsoll (2.0) (fjerne og montere).
  4. Reinstall the vehicle software. See Installer programvare på nytt – berøringsskjerm.
  5. Åpne Servicemodus Pluss. Se Servicemodus Pluss
  6. På berøringsskjermen berører du Service Mode (Servicemodus) > Safety and Restraints (Sikkerhet og sikring) > Airbags (Kollisjonsputer) > RCM > Post Replacement Tasks (Oppgaver etter utskifting).
  7. På neste skjermbilde berører du Run (Kjør) og lar rutinen fullføres.
  8. On the touchscreen, check the headlight leveling system.
    • If the headlight leveling system is "Ride Height Sensor", exit Service Mode, see Servicemodus, and discontinue this procedure.
    • If the headlight leveling system is "Virtual Pitch Sensor", exit Service Mode, see Servicemodus, and continue to the next step.
  9. Adjust the headlights: