2026-09-01

Tire Rotation (Mobile Only)

Korrigeringskode 34020105 FRT 0.48 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og dens tilhørende FRT alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se Forholdsregler for ergonomi for trygge og sunne arbeidspraksiser.

  • 2026-08-27: Released new procedure.
Merk
Denne prosedyren gjelder for biler med like hjul og retningsuavhengige dekk. Se nedenfor for veiledning om rotering av ulike hjul eller retningsavhengige dekk:
  • Ulike hjul med retningsuavhengige dekk. Jekk opp venstre og høyre forside av bilen for å rotere frontdekkene, eller jekk opp venstre og høyre bakside av bilen for å rotere bakdekkene:
  • Like hjul med retningsavhengige dekk. Jekk opp venstre forside og venstre bakside av bilen for å rotere de venstre dekkene, eller jekk opp høyre forside og høyre bakside av bilen for å rotere de høyre dekkene:

Vehicle ride quality and handling are maximized when all 4 tires are the same age, model, and tread depth. Rotating tires regularly allows them to wear at the same rate and increases the service life. Tesla recommends tire rotation every 6,250 miles (10,000 km) or if tread depth difference is 2/32 in (1.5mm) or greater, whichever comes first.

Merk
Tesla recommends replacing tires in pairs unless the other tires are within 2/32 in (1.5 mm) of tread depth of the new tire.
Merk
If only 2 new tires are installed, the new tires must be installed on the rear of the vehicle. In wet conditions, the tires that have less tread have less traction than the new tires. Reduced traction at the front of the vehicle leads to understeer, which most drivers are better able to react to than the oversteer that would result if the worn tires were on the rear of the vehicle.
Merk
Tesla recommends replacing a tire if any of the tread depths are 4/32 in (3 mm) or less.
Merk
Model Y is pictured, but this procedure can be performed on Model 3.

Prosedyre

  1. Ensure the vehicle is parked on a level surface.
  2. Install wheel chocks on the RH front wheel.
  3. Remove the LH rear wheel cap, if equipped. See Kapsel – hjul (fjerne og skifte ut).
  4. Loosen LH rear wheel lug nuts (x5)
    Merk
    5x nuts, 21mm, 175 Nm
    ADVARSEL
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  5. Remove the LH front wheel cap. See Kapsel – hjul (fjerne og skifte ut).
  6. Loosen LH front wheel lug nuts (x5).
    Merk
    5x nuts, 21mm, 175 Nm
    ADVARSEL
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  7. Jack up the LH rear of the vehicle.
    Merk
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
    Merk
    Raise the vehicle until the LH front wheel is off the ground.
  8. Position jack stands underneath the LH front and LH rear of the vehicle.
    ADVARSEL
    Hvis en elektrisk eller pneumatisk jekk brukes, må du unngå skade ved å holde avstand fra bilen før den heves.
    Merk
    Align the jack stand cutout with the floor jack.
    Merk
    Align the top opening of the jack stand with the bottom of the jack stand adapter.
  9. Slowly lower the floor jacks, making sure the LH front and rear jack stands are aligned with the jack stand adapters.
    Merk
    Perform a shake test to verify stability.
  10. Remove the lug nuts from the wheel, and then remove the LH rear wheel from the vehicle.
    Merk
    5x nuts, 21mm, 175 Nm
  11. Remove the lug nuts from the wheel, and then remove the LH front wheel from the vehicle.
    Merk
    5x nuts, 21mm, 175 Nm
  12. Swap the LH rear wheel with the LH front wheel and install the LH wheels.
    Merk
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    ADVARSEL
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  13. Raise the vehicle off the LH rear and LH front jack stands.
    Merk
    Jack up the LH rear of the vehicle until the LH front wheel is off the jack stand.
  14. Remove the LH front and LH rear jack stands (x2), and then lower the vehicle.
  15. Remove the chocks from the RH front wheel.
  16. Install wheel chocks on the LH front wheel.
  17. Remove the RH rear wheel cap. See Kapsel – hjul (fjerne og skifte ut).
  18. Loosen RH rear wheel lug nuts (x5).
    Merk
    5x nuts, 21mm, 175 Nm
    ADVARSEL
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  19. Remove the RH front wheel cap. See Kapsel – hjul (fjerne og skifte ut).
  20. Loosen RH front wheel lug nuts (x5).
    Merk
    5x nuts, 21mm, 175 Nm
    ADVARSEL
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  21. Jack up the RH rear of the vehicle.
    Merk
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
    Merk
    Raise the vehicle until the RH front wheel is off the ground.
  22. Position jack stands underneath the RH front and RH rear of the vehicle.
    ADVARSEL
    Hvis en elektrisk eller pneumatisk jekk brukes, må du unngå skade ved å holde avstand fra bilen før den heves.
    Merk
    Align the jack stand cutout with the floor jack.
    Merk
    Align the top opening of the jack stand with the bottom of the jack stand adapter.
  23. Slowly lower the floor jacks, making sure the RH front and rear jack stands are aligned with the jack stand adapters.
    Merk
    Perform a shake test to verify stability.
  24. Remove the lug nuts from the wheel, and then remove the RH rear wheel from the vehicle.
    Merk
    5x nuts, 21mm, 175 Nm
  25. Remove the lug nuts from the wheel, and then remove the RH front wheel from the vehicle.
    Merk
    5x nuts, 21mm, 175 Nm
  26. Swap the RH rear wheel with the RH front wheel and install the RH wheels.
    Merk
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    ADVARSEL
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  27. Raise the vehicle off the RH rear and RH front jack stands.
    Merk
    Jack up the RH rear of the vehicle until the RH front wheel is off the jack stand.
  28. Remove the RH front jack stand, and then lower the vehicle.
  29. Jack up the LH rear of the vehicle.
    Merk
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
  30. Slowly lower the floor jack, making sure the LH rear jack stand is aligned with the jack stand adapter.
    Merk
    Perform a shake test to verify stability.
  31. Remove the lug nuts from the wheel, and then remove the LH rear wheel from the vehicle.
    Merk
    5x nuts, 21mm, 175 Nm
  32. Remove the lug nuts from the wheel, and then remove the RH rear wheel from the vehicle.
    Merk
    5x nuts, 21mm, 175 Nm
  33. Swap the RH rear wheel with the LH rear wheel and install the rear wheels.
    Merk
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    ADVARSEL
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  34. Remove the LH rear jack stand, and then lower the vehicle.
  35. Remove the RH rear jack stand and then lower the vehicle.
  36. Torque all 4 rear wheels.
    Merk
    5x nuts, 21mm, 175 Nm
  37. Install all 4 wheel caps. See Kapsel – hjul (fjerne og skifte ut).
  38. Remove the chocks from the LH front wheel.
  39. Open the LH front door.
  40. Unlock vehicle gateway. See Gateway (lås opp).
  41. Tap Controls > Chassis > Alignment & Tire > Reset Learned Tire Values, and click Run.
    Merk
    Click Close once the routine is completed.
  42. Tap Controls > Service > Wheel & Tire > Tires, choose the tire season and click Reset. After resetting, check if the Tire Service Mileage in the upper right corner is displayed as Less than 500 km ago.
  43. Exit Service Mode.
  44. Close the LH Front door.
  45. Inform the customers that a short calibration drive cycle might be required.