2026-08-10

Quarter Inner Section (LH) – Vehicles Built for China After October 3, 2017

Correction code: 10101902702 10101902402 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair and Service repair work required to perform this procedure, including the linked Collision Repair procedures and linked Service procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Depending on the damage to the vehicle, additional repairs may be required.

Parts List

Quantity Description Image / Notes
1 MX ASY - REAR QUARTER INNER PNL CHINA (Quarter Inner – LH – Vehicles Built for China After October 3, 2017)
19 Structural Bulb Rivet, 6.5 mm

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the Insulator - Wheelhouse - Rear - LH (Remove and Replace).
  2. Remove the Wheel Assembly (Remove and Install).
  3. Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
  4. Remove the Air Spring Module - Rear - LH (Remove and Replace).
  5. Remove the Fascia Assembly - Rear (Remove and Install).
  6. Remove the Glass - Rear Quarter Window - LH (Remove and Install).
  7. Remove the Taillight Assembly - LH (Remove and Replace).
  8. Remove the Charge Port (Type 2) (Remove and Replace).
  9. Remove the Charger (Remove and Replace).
  10. Remove the Quarter Outer - Vehicles Built for China.
  11. Remove the Rear Wheel Arch.
  12. Remove the Quarter Outer - Vehicles Built for China.
  13. Remove the necessary portion of the Rear Wheel Arch.
  14. Remove the original component.
    or Factory Spot Welds
    • A = 5 mm.
    • B = 30 mm.
    • C = 15 mm.
    Note
    Do not remove spot welds used for measuring. Instead, cut 15 mm. to the rear of the indicated spot welds.

    Cut Line

    Reference Line/Point

  15. Make the new component by cutting the new Quarter Inner service part.
    Note
    Using the removed portion of the old component as a template, cut the service part 30 mm larger than the removed portion of the old component. The additional 30 mm will create an overlap joint with the component still on the vehicle.

    Cut Line

    Reference Line/Point

    • B = 30 mm.
    Note
    At the top front area where the new component will be installed, trim the new component as needed to obtain a good butt joint.
  16. Prepare for installation.
    or Structural Bulb Rivets, 6.5 mm
    • A = 5 mm.
    • C = 15 mm.
    • D = 40 mm.
    • E = 94 mm.

    GMA Weld

  17. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  18. Install the new component or components.
  19. Perform GMA welding.
    GMA Weld
    Warning
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to Approved Gas Metal Arc (GMA) Welders and Welding Wire for information on approved GMA welders and welding wire.
    CAUTION
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Note
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  20. Install the necessary portion of the Rear Wheel Arch.
  21. Install the Quarter Outer - Vehicles Built for China.
  22. Perform any necessary post-repair operations.
  23. Install the Rear Wheel Arch.
  24. Install the Quarter Outer - Vehicles Built for China.
  25. Install the Charger (Remove and Replace).
  26. Install the Charge Port (Type 2) (Remove and Replace).
  27. Install the Taillight Assembly - LH (Remove and Replace).
  28. Install the Glass - Rear Quarter Window - LH (Remove and Install).
  29. Install the Fascia Assembly - Rear (Remove and Install).
  30. Install the Air Spring Module - Rear - LH (Remove and Replace).
  31. Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
  32. Install the Wheel Assembly (Remove and Install).
  33. Install the Insulator - Wheelhouse - Rear - LH (Remove and Replace).