03/07/2024 16:04:53

Quarter Inner Section (LH)

Parts List

Quantity Description Image / Notes
1 ASY - REAR QTR INNER PNL LH (Quarter Inner – LH)
7 SPR, 5x4.5
3 SPR, 5x7

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the .
  2. Remove the necessary portion of the Rear Wheel Arch.
  3. Remove the original component.
    or Factory Spot Welds

    Cut Line

    Reference Line/Point

    • A = 60 mm.
    • B = 100 mm.
    • C = 160 mm.
    • D = 30 mm.
    • E = 80 mm.
  4. Make the new component by cutting the new Quarter Inner service part.
    Informational PurposesAn informational icon, calling your attention
    Note
    Using the removed portion of the old component as a template, cut the service part as specified below to create a service part larger than the removed portion of the old component. The new component should overlap the the remaining portion of the panel along the forward joint by 25 mm. The new component should should overlap the remaining portion of the panel along the rear joint by 92 mm.

    Cut Line

    Reference Line/Point

    • F = 25 mm.
    • G = 172 mm.
    Informational PurposesAn informational icon, calling your attention
    Note
    In the wheel arch area where the new component will be installed, trim the new component as needed to obtain a good butt joint.
  5. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    A red X indicates a location where a factory-installed fastener is not being replaced.
    or SPRs, 5x4.5
    Informational PurposesAn informational icon, calling your attention
    Note
    The following Tesla SPR die is required to install this SPR: KA 075 2113.
    or SPRs, 5x7
    Informational PurposesAn informational icon, calling your attention
    Note
    The following Tesla SPR die is required to install the SPR circled in red: SM 085 0125. Use Tesla SPR die FM 090 2120 to install the SPRs that are not circled in red.

    GMA Weld

  6. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  7. Install the new component or components.
  8. Perform GMA welding.
    GMA Weld
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to Approved Gas Metal Arc (GMA) Welders and Welding Wire for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Note
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  9. Install the necessary portion of the Rear Wheel Arch.
  10. Install the .
  11. Perform any necessary post-repair operations.