2026-08-09

Brightwork - Upper - LH (Remove and Replace)

Correction code 12200302 0.48 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il relativo FRT associato, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

Torque Specifications

Tabella 1. Torque Specifications: Brightwork - Upper - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws that attach the brightwork to the body
1 Nm (.7 lbs-ft)
  • Torx T20 socket
 Reuse
Grommets Replace 1106827-00-C

Remove

  1. Open the LH doors and fully lower the LH windows.
  2. Pull down to release the front and rear primary body seals from the LH upper brightwork.
    Note
    Start from the upper corner closest to the B-pillar applique, and then pull straight down along the length of the seal to fully release the seal from the upper brightwork.
  3. Remove the LH B-pillar applique. See .
  4. Release the LH header seal from the LH upper brightwork. See Seal - Header - LH (Remove and Replace).
  5. Remove the screws (x5) that attach the front portion of the LH upper brightwork to the body.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  6. Remove the push rivet that attaches the LH front of the bright trim to the body.
  7. Remove the screws (x3) that attach the rear portion of the LH upper bright work to the body.
  8. With assistance, remove the LH upper bright work from the vehicle
    Note
    Start from the front of the trim and work rearward. The rear of the trim engages the rear quarter glass.
    CAUTION
    Be careful not to damage paint and/or quarter glass when removing the trim.
  9. Remove and discard the grommets (x8) from the body.

Install

  1. Install new grommets (x8) into the body where the LH upper brightwork will install.
  2. With assistance, carefully position the LH upper brightwork onto the vehicle.
    Note
    Starting at the rear quarter glass, ensure the bright trim is fully seated on the dowel protruding out of the rear quarter glass.
  3. Install the screws that attach the front portion of the LH upper brightwork to the body.
    1 Nm (.7 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  4. Install the push rivet that attaches the LH front of the bright trim to the body.
  5. Install the screws that attach the rear portion of the LH upper brightwork to the body.
    1 Nm (.7 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  6. Install the LH header seal onto the LH upper brightwork. See Seal - Header - LH (Remove and Replace).
  7. Install the B-pillar applique. See .
  8. Press up to fasten the rear and front primary body seals onto the LH upper brightwork.
    Note
    Work from the rear corner of each seal forward, and make sure that the seal fully engages the brightwork. When installed correctly, the seal edge is not visible.
  9. Work each seal around the opening so as to evenly distribute it.
    Note
    Make sure to push the seal into each corner.
  10. Close the LH doors and fully raise the LH windows.