2026-08-09

Seat Back - 2nd Row - LH (Remove and Replace)

Correction code 13054002 0.30 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il relativo FRT associato, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2024-07-23: Deleted the seatback cushion separation steps.
  • 2024-08-15: Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.
Apparecchiatura:
  • Torchless Heat Induction Tool - 2152873-00-A

Torque Specifications

Tabella 1. Torque Specifications: Seat Back - 2nd Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x5) that attach the LH 2nd row seat back frame to the vehicle
37 Nm (27.3 lbs-ft)
  • 11 mm socket
Replace
Avvertenza
Bolts must be installed in the following sequence:
  1. Front Outboard
  2. Rear Inboard
  3. Rear Outboard
  4. Front Inboard

Remove

  1. Remove the LH lower C-pillar trim. See .
  2. Release the clips (x3) that attach the main carpet to the lower seat cushion frames.
  3. Remove the bolts (x5) that attach the LH 2nd row seat back frame to the vehicle.
    Nota
    The two frontmost bolts are behind the main carpet.
    Suggerimento
    Use of the following tool(s) is recommended:
    • 11 mm socket
  4. Carefully fold down the LH 2nd row seat back.
    Avvertenza
    Place a protective covering on the seat back upholstery and take care not to damage the upholstery during removal of the seat back.
    Avvertenza
    Do not place any additional weight on the seat back. Doing so may damage the seat frame alignment tabs, which can cause unevenness between the 60 and 40 seat backs.
  5. Disconnect the electrical harness from the connector at the LH lower seat frame.
  6. With assistance, carefully remove the LH 2nd row seat back assembly from the vehicle.
    Avvertenza
    Place the seat back assembly in an area where it will not be tipped over or otherwise damaged.
    Nota
    For NA only: If the 2nd row seat that is not being replaced does not have ISOFIX flag for child locks, replace the seat cover.. See .

Install

  1. With assistance, position the LH 2nd row seatback assembly into place, and then connect the electrical harness to the connector at the LH lower seat frame.
  2. Move the LH 2nd row seatback to vertical position.
  3. Install the bolts (x5) that attach the LH 2nd row seat back frame to the vehicle.
    37 Nm (27.3 lbs-ft)
    Note
    The two frontmost bolts are behind the main carpet.
    Note
    Torque in the sequence of:
    1. Front Outboard
    2. Rear Inboard
    3. Rear Outboard
    4. Front Inboard
    Tip
    Use of the following tool(s) is recommended:
    • 11 mm socket
  4. Install the clips (x3) that attach the main carpet to the lower seat cushion frames.
  5. Install the LH lower C-pillar trim. See .