2026-08-09

Retractor - Seatbelt - 1st Row - LH (Remove and Replace)

Correction code 20054102 0.36 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il relativo FRT associato, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

Equipment:
  • 1133787-00-A Key, Seat Belt Release, Model 3
  • 2024-11-26: Adjust the steps sequence based on feedback from engineering team.

Torque Specifications

Table 1. Torque Specifications: Retractor - Seatbelt - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Patch bolt that attaches the upper D-ring to the adjustable top loop
30 Nm (22.1 lbs-ft)
  • Torx T50 socket
 Replace
Bolts that attach the seat belt webbing guide to the B-pillar
5 Nm (3.7 lbs-ft)
  • 8 mm socket
 Replace
Patch bolt that attaches the seat belt retractor to the base of the B-pillar
40 Nm (29.5 lbs-ft)
  • 13 mm 12-point deep socket
 Replace

Remove

  1. Open the LH doors and lower the LH windows.
  2. Remove the LH instrument panel end cap. See .
  3. Remove the LH middle A-pillar trim. See #GUID-E1DDEA4B-6FBC-438D-997F-B3BD26910740.
  4. Remove the LH lower A-pillar trim. See #GUID-2B48046D-F15C-4E02-B2C9-82D80BB25389.
  5. Remove the lower portion of the LH front door seal from the body.
  6. Remove the LH front seat harness guide from the body.
  7. Move the front seats fully forward.
  8. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  10. Insert the seat belt release key (1133787-00-A) into the bottom of the seatbelt pretensioner coupling to release the seatbelt from the pretensioner.
  11. Remove the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  12. Release the 2nd row seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  13. Partially remove the lower portion of the LH rear door seal.
  14. Remove the LH lower C-pillar trim. See .
  15. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Non-Structural Pack) (Remove and Replace)
  16. Remove and discard the bolts that attach the seat belt webbing guide to the B-pillar, and then remove the guide from the B-pillar.
    Tip
    Use of the following tool(s) is recommended:
    • 8 mm socket
  17. Remove and discard the patchbolt that attaches the upper D-ring to the top loop.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  18. Remove and discard the patchbolt that attaches the seat belt retractor to the base of the B-pillar.
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm 12-point deep socket
  19. Disconnect the electrical harness from the seat belt retractor connectors (x2).
    Note
    For better access to the connectors, the retractor can be removed from the B-pillar first.
  20. Remove the LH front seatbelt from the vehicle.

Install

  1. Install the LH front seatbelt into the vehicle.
  2. Connect the electrical harness to the seat belt retractor connectors (x2).
  3. Install a new patchbolt to attach the seat belt retractor to the base of the B-pillar.
    40 Nm (29.5 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm 12-point deep socket
  4. Install a new patchbolt to attach the upper D-ring to the top loop.
    30 Nm (22.1 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  5. Install the seat belt webbing guide to the B-pillar, and then install new bolts that attach the guide to the B-pillar.
    5 Nm (3.7 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 8 mm socket
  6. Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Non-Structural Pack) (Remove and Replace)
  7. Install the LH lower C-pillar trim. See .
  8. Install the lower portion of the LH rear door seal that was partially removed.
  9. Install the 2nd row seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  10. Install the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  11. Install the LH front seatbelt pretensioner coupling onto the LH front seat pretensioner.
    Note
    Perform a pull-push-pull test to verify the pretensioner and coupling are fully engaged.
    Warning
    I video inclusi in questa procedura hanno il solo scopo di fornire una panoramica supplementare. Seguire tutti i passaggi elencati nella procedura per evitare danni ai componenti e/o lesioni personali.
  12. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  14. Move the front seats fully rearward.
  15. Install the LH front seat harness guide to the body.
  16. Install the lower portion of the LH front door seal to the body.
  17. Install the LH lower A-pillar trim. See #GUID-2B48046D-F15C-4E02-B2C9-82D80BB25389.
  18. Install the LH middle A-pillar trim. See #GUID-E1DDEA4B-6FBC-438D-997F-B3BD26910740.
  19. Install the LH instrument panel end cap. See .
  20. Perform a pull test on the belt to ensure proper installation. Pull webbing up with force to ensure the pretensioner coupler was properly installed. Next, pull out all the webbing from the retractor. Webbing should smoothly retract after you have pulled it all out. Lastly, quickly tug at the webbing in a downward motion, retractor should lock.
  21. Close the LH doors and raise the LH windows.