2026-08-09

Knuckle - Suspension - Front - LH (Dual Motor) (Remove and Replace)

Correction code 31010112 0.72 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il relativo FRT associato, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

    Torque Specifications

    Tabella 1. Torque Specifications: Knuckle - Suspension - Front - LH (Dual Motor) (Remove and Replace)
    Description Torque Value Recommended Tools Reuse/Replace Notes
    Bolts that attach the LH front brake dust shield to the knuckle
    8 Nm (5.9 lbs-ft)
    • Torx T30 socket
    		Reuse
    Bolt that attaches the LH front ABS wheel speed sensor to the LH front suspension knuckle
    5 Nm (3.7 lbs-ft)
    • 10 mm deep socket
    		Reuse
    Nut that attaches the LH tie rod end to the LH front suspension knuckle
    180 Nm (132.7 lbs-ft)
    • 22 mm socket
    • 12 pt 10mm combination wrench
    • 12 pt 22 mm combination wrench
    		 Replace 1109263-00-B
    Nut that attach the LH upper control arm to the LH front suspension knuckle
    56 Nm (41.3 lbs-ft)
    • Torx T47 socket
    • 12 pt 15 mm combination wrench
    		 Replace 1111145-00-A
    Nut that attaches the LH front lower compliance link to the front suspension knuckle
    180 Nm (132.7 lbs-ft)
    • 22 mm socket
    • Torx T45 socket
    		Replace 1109263-00-B
    Nut that attaches the LH front lower lateral link to the LH front suspension knuckle
    180 Nm (132.7 lbs-ft)
    • 22 mm socket
    • 22 mm ratcheting combination wrench
    • Torx T45 socket
    		Replace 1109263-00-B

    Remove

    1. Remove the LH front hub. See .
    2. Remove the bolts that attach the LH front brake dust shield to the knuckle, and then remove the dust shield from the vehicle.
      Tip
      Use of the following tool(s) is recommended:
      • Torx T30 socket
    3. Remove the bolt that attaches the LH front ABS wheel speed sensor to the LH front suspension knuckle.
      Tip
      Use of the following tool(s) is recommended:
      • 10 mm deep socket
    4. Release the clips that attach the LH front ABS wheel speed sensor electrical harness to the LH front suspension knuckle.
    5. Remove and discard the nut that attaches the LH tie rod end to the LH front suspension knuckle, and then remove the tie rod end from the knuckle.
      Tip
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 12 pt 10mm combination wrench
      • 12 pt 22 mm combination wrench
    6. Remove the bolt and discard the nut that attach the LH upper control arm to the LH front suspension knuckle.
      Note
      Compress the joint to remove the bolt.
      Tip
      Use of the following tool(s) is recommended:
      • Torx T47 socket
      • 12 pt 15 mm combination wrench
    7. Remove and discard the nut that attaches the LH front lower compliance link to the front suspension knuckle.
      Tip
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • Torx T45 socket
    8. Remove and discard the nut that attaches the LH front lower lateral link to the LH front suspension knuckle.
      Tip
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 22 mm ratcheting combination wrench
      • Torx T45 socket
    9. Remove the LH front suspension knuckle from the vehicle.

    Install

    1. Position the LH front suspension knuckle into the vehicle.
    2. Rest the LH front drive unit half shaft in the LH front suspension knuckle, and then install a new nut that attaches the knuckle to the lower lateral link.
      180 Nm (132.7 lbs-ft)
      Suggerimento
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 22 mm ratcheting combination wrench
      • Torx T45 socket
    3. Install a new nut that attaches the LH front lower compliance link to the LH front suspension knuckle.
      180 Nm (132.7 lbs-ft)
      Suggerimento
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • Torx T45 socket
    4. Install the bolt and new nut that attach the LH upper control arm to the LH front suspension knuckle.
      56 Nm (41.3 lbs-ft)
      Suggerimento
      Use of the following tool(s) is recommended:
      • Torx T47 socket
      • 12 pt 15 mm combination wrench
    5. Install a new nut that attaches the LH tie rod end to the LH front suspension knuckle.
      180 Nm (132.7 lbs-ft)
      Suggerimento
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 12 pt 10mm combination wrench
      • 12 pt 22 mm combination wrench
    6. Install the clips that attach the LH front ABS wheel speed sensor electrical harness to the LH front suspension knuckle.
    7. Install the bolt that attaches the LH front ABS wheel speed sensor to the LH front suspension knuckle.
      5 Nm (3.7 lbs-ft)
      Suggerimento
      Use of the following tool(s) is recommended:
      • 10 mm deep socket
    8. Install the bolts that attach the LH front brake dust shield to the knuckle.
      8 Nm (5.9 lbs-ft)
      Suggerimento
      Use of the following tool(s) is recommended:
      • Torx T30 socket
    9. Install the LH front hub. See .
    10. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See .