2026-08-09

Airbag - Curtain - LH (Remove and Replace)

Correction code 20012002 1.62 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il relativo FRT associato, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2026-02-20: Added note on using PROC_RCM_DISARM if using this procedure to diagnose the SRS.
  • 2-5-2024: Added note on varying number of curtain airbag fasteners.
Avvertenza
If using this procedure to diagnosis the vehicle's Supplemental Restraint Systems (SRS), disarm the RCM, which will prevent all airbags and pretensioners from deploying. Re-arm the RCM after all of the vehicle's SRS components are re-installed.
  • Disarm RCM:PROC_RCM_DISARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Disarm RCM
    • Safety & Restraints ➜ Seats ➜ Disarm RCM
    via Toolbox:(link)
  • Re-arm RCM:PROC_RCM_ARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Re-Arm RCM
    • Safety & Restraints ➜ Seats ➜ Re-Arm RCM
    via Toolbox:(link)
Avvertenza
Assicurarsi che l'alimentazione a 12 V/bassa tensione sia stata scollegata per almeno 1 minuto prima di scollegare il cablaggio elettrico dai componenti del sistema di ritenuta supplementare (SRS) come il modulo di controllo ritenuta, sensori, airbag ecc. Scollegare la batteria a 12V/bassa tensione e il circuito di primo soccorso. La mancata osservanza di queste precauzioni può causare comportamenti inattesi del sistema di sicurezza. Per ulteriori informazioni sulle precauzioni per il sistema SRS, vedere .

Torque Specifications

Tabella 1. Torque Specifications: Airbag - Curtain - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the LH curtain airbag to the body
9 Nm (6.6 lbs-ft)
  • 10 mm socket
 Reuse

Remove

  1. Open all doors and fully lower all windows.
  2. Open the liftgate.
  3. Remove the front headliner. See .
  4. Remove the rear headliner. See Headliner - Rear (Remove and Replace).
  5. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  6. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  7. Disconnect the electrical harness from the LH curtain airbag connector.
  8. Remove the bolts that attach the front and center portions of the LH curtain airbag to the body.
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  9. Remove the bolts that attach the rear portion of the LH curtain airbag to the body.
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  10. Carefully release the clips (x8) that attach the LH curtain airbag to the side rail, and remove the airbag from the vehicle.
    Warning
    If any clips are damaged, the airbag must be replaced.
    Warning
    The airbag should always be handled by the igniter; the igniter should never be left dangling.
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.

Install

  1. Install the LH curtain airbag to the side rail, and then carefully fasten the clips (x8) that attach the airbag to the side rail.
    Warning
    If any clips are damaged, the airbag must be replaced.
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  2. Install and hand-tighten the bolts that attach the rear portion of the LH curtain airbag to the body.
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  3. Install and hand-tighten the bolts that attach the front and center portions of the LH curtain airbag to the body.
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  4. Torque the bolts that attach the LH curtain airbag to the body.
    9 Nm (6.6 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Connect the electrical harness to the LH curtain airbag connector.
  6. Install the rear headliner. See Headliner - Rear (Remove and Replace).
  7. Install the front headliner. See .
  8. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  9. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).