2026-08-09

Hinge - Door - Front - Upper - LH (Remove and Replace)

Correction code 11336402 0.18 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il relativo FRT associato, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

Torque Specifications

Table 1. Torque Specifications: Hinge - Door - Front - Upper - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH front upper door hinge to the body
24 Nm (17.7 lbs-ft)
  • Combination Wrench 12pt 13mm
 Reuse
Bolt/Nut that attaches the LH front upper door hinge to the door
49 Nm (36.1 lbs-ft)
  • Combination Wrench 12pt 13mm
 Reuse

Remove

  1. Open the LH front door and lower the window.
  2. Use a jack to support the LH front door from the bottom.
  3. Apply masking tape to the area surrounding the LH front door upper hinge on the body and door to aid in alignment during installation.
  4. Remove the bolts (x2) that attach the LH front upper door hinge to the body.
    Tip
    Use of the following tool(s) is recommended:
    • Combination Wrench 12pt 13mm
  5. Remove the fastener that attaches the LH front upper door hinge to the door.
    Note
    The fastener can either be a bolt or a nut.
    Tip
    Use of the following tool(s) is recommended:
    • Combination Wrench 12pt 13mm
  6. Carefully remove the LH front upper door hinge from the vehicle.

Install

  1. Position the LH front door upper hinge to original position.
    Note
    Push outward on the top of the door near the speaker with one hand and then insert the upper hinge.
  2. Hand-tighten the bolts (x2) that attach the LH front upper door hinge to the body.
  3. Hand-tighten the fastener that attaches the LH front upper door hinge to the door.
    Note
    The fastener can either be a bolt or a nut.
  4. Close the LH front door.
  5. Check the gap and flushness and adjust if necessary. Refer to CVIS for current specification.
  6. Open the LH front door.
  7. Torque the bolts (x2) that attach the LH front upper door hinge to the body.
    24 Nm (17.7 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Combination Wrench 12pt 13mm
  8. Torque the fastener that attaches the LH front upper door hinge to the door.
    49 Nm (36.1 lbs-ft)
    Note
    The fastener can either be a bolt or a nut.
    Tip
    Use of the following tool(s) is recommended:
    • Combination Wrench 12pt 13mm
  9. Remove the masking tape.
  10. Apply touch up paint on the LH front door hinge bolts as needed.
    Note
    Shake the touch up paint before applying. Allow the first coat to dry for 20 minutes before applying a second coat.
  11. Raise the LH front window and close the LH front door.