2025-11-04

도어 - 충전 포트(CP)(전 세계 공통)(조정)

교정 코드 44011500 1.02 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.

  • 2025-10-21: Moved gap and flush inspection to beginning. Included links to sub-procedures.
  • 2023-08-25: Added link to charge port voltage check procedure.
Informational PurposesAn informational icon, calling your attention
참고
This procedure applies to the Global-style charge port door.

Remove

  1. Perform a gap and flush inspection with the charge port door closed. Note the measurements.
    Informational PurposesAn informational icon, calling your attention
    참고
    If the measurements are within specification, do not continue with adjustment.
    Area (see figure) Specification Value
    1 Flush target to body N/A
    Flush target to lamp 0 mm
    2 Flush target to body 1.2 mm
    3 Flush target to body 1.2 mm
    Flush target to lamp 0 mm
  2. Remove the rear sill panel. See 트림 - 실 패널 - 후면 - LH(탈거 및 교체).
  3. Open the charge port door.
  4. Open the liftgate.
  5. 트렁크 사이드 트림 브래킷을 탈거합니다. 참조 항목:
  6. 3열 시트 쿠션을 탈거합니다(장착된 경우). 참조 항목: 쿠션 - 시트 - 3열(탈거 및 교체).
  7. Disconnect LV power. See LV 전원(연결 해제 및 연결).
  8. Verify that high voltage is no longer available to the charge port. See 충전 포트(CP) 전압 점검.
  9. Remove the LH inner reinforcement. See 보강재 - 내부 - LH(탈거 및 교체).
  10. Release the charge port latch connection.
    Informational PurposesAn informational icon, calling your attention
    참고
    Take note of the harness routing.
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull the red locking tab outwards to release lock, then pull again to release connector.
  11. Release the charge port connection.
    Informational PurposesAn informational icon, calling your attention
    참고
    Carefully remove the white locking tab, depress the tab to release the connection from the charge port, then pull the connector out.
    Informational PurposesAn informational icon, calling your attention
    참고
    The connection is intended to disengage the safety cap when released.
  12. Remove the charge port safety cap.
  13. Remove the nuts (x2) that secure the charge port busbar to the charge port. Remove the busbar leads from the studs.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 11mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    The nuts have captive washers. Take caution of any tension present with the busbar
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    The busbar may be under tension. Use caution to avoid damage upon removal.
  14. Remove the bolts (x4) that secure the charge port assembly, then remove the assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
  15. Remove the bolt that secures the charge port door to the vehicle body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 8mm 소켓

Adjust

  1. Turn the top hex insert clockwise to extend the insert or counter-clockwise to shorten the spacing to meet the desired flush measurement for the charge port door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 5mm 육각
    Informational PurposesAn informational icon, calling your attention
    참고
    The compensator is ~3 mm out from the back of the hex face to the top of the thread housing. It can be adjusted an additional 2 mm in either direction, leaving the total distance between 1 mm and 5 mm.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Push the datum slightly outwards for easier access to the hex insert.
  2. Turn the front hex insert clockwise to extend the insert or counter-clockwise to shorten the spacing to meet the desired flush measurement for the charge port door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 5mm 육각
    Informational PurposesAn informational icon, calling your attention
    참고
    The compensator is ~3 mm out from the back of the hex face to the top of the thread housing. It can be adjusted an additional 2 mm in either direction, leaving the total distance between 1 mm and 5 mm.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Push the datum slightly outwards for easier access to the hex insert.
  3. Turn the bottom hex insert clockwise to extend the insert or counter-clockwise to shorten the spacing to meet the desired flush measurement for the charge port door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 5mm 육각
    Informational PurposesAn informational icon, calling your attention
    참고
    The compensator is ~3 mm out from the back of the hex face to the top of the thread housing. It can be adjusted an additional 2 mm in either direction, leaving the total distance between 1 mm and 5 mm.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Push the datum slightly outwards for easier access to the hex insert.

Install

  1. Install the bolt that secures the charge port door to vehicle body.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 8mm 육각
  2. Install the charge port assembly into vehicle and torque the bolts (x4).
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    New charge ports come pre-applied with Penetrox.
  3. Clean the charge port assembly busbar contact surfaces with isopropyl alcohol to remove any residual Penetrox. Allow 1 minute to dry.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use a plastic trim tool to push the alcohol wipe down between the plastic divider.
  4. Clean the busbar lead contact surfaces with isopropyl alcohol to remove any residual Penetrox.
    Informational PurposesAn informational icon, calling your attention
    참고
    Allow 1 minute for IPA to dry.
  5. Apply Penetrox to the backside of the busbar leads.
    Informational PurposesAn informational icon, calling your attention
    참고
    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads. Spread evenly to verify the contact surface is fully covered
  6. Install the charge port busbar leads to the charge port assembly. Torque the nuts (x2).
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 11mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    The nuts have captive washers.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    If excessive force is required to seat busbars, they may have been bent. Inspect for damage and replace if necessary.
  7. Inspect HV insulating gloves
  8. Put on HV insulating gloves and leather over gloves.
  9. Perform Hioki resistance test at each HV joint (x2) from the HV busbar lead to charge port stud.
    • If the resistance is greater than 0.270 mΩ (270 μΩ), remove the fastener, clean the areas with isopropyl alcohol, install fastener back, and retest.
    • If the resistance is less than 0.050 mΩ (50 μΩ), reposition the probe and measure again. If the measurement is under 0.050 mΩ again, proceed to the next step.
  10. Remove the leather over gloves and HV insulating gloves.
  11. Install the charge port safety cap.
    Informational PurposesAn informational icon, calling your attention
    참고
    Engage hooks (x2). The safety cap clicks into position.
  12. Secure the charge port connection.
    Informational PurposesAn informational icon, calling your attention
    참고
    Fully engage the connection and the white locking tab.
  13. Secure the charge port latch connection.
    Informational PurposesAn informational icon, calling your attention
    참고
    Return harness to original routing. The harness sits in front of the busbar. Fully engage the connector and red locking tab.
  14. Install the LH inner reinforcement and all trim that was removed. See 보강재 - 내부 - LH(탈거 및 교체).
  15. Reconnect LV power. See LV 전원(연결 해제 및 연결)
  16. Close the liftgate
  17. Install the rear sill panel. See 트림 - 실 패널 - 후면 - LH(탈거 및 교체).
  18. Calibrate the LH and RH falcon wing doors.
    Informational PurposesAn informational icon, calling your attention
    참고
    Hold the upper B-pillar button in the down position to manually calibrate.
  19. Move the LH front seat to the original position.