2024-12-17
센서 - HVAC - 윈드실드(탈거 및 교체)
Correction code
10206002 0.24
바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.
참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면ServiceManualFeedback@tesla.com으로 이메일을 보내십시오.
참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.
경고
This procedure is a DRAFT.
Although it has been validated, Warnings and Cautions might be missing. Follow safety
requirements and use extreme caution when working on or near High Voltage systems and
components.
- 2024-12-02: 참고 사항 및 정비 모드 지침을 업데이트했습니다.
탈거
- 하단 쿼드 카메라 커버를 탈거합니다. 참조 항목: 카메라 커버 - 하단(탈거 및 교체).
- 리어 뷰 미러를 탈거합니다. 참조 항목: 미러 - 후방(탈거 및 교체).
- 상단 쿼드 카메라 커버를 탈거합니다. 참조 항목: 상단 커버 - 리어 뷰 미러(탈거 및 교체).
-
윈드실드 HVAC 센서 전기 커넥터를 연결 해제합니다.
-
윈드실드 HVAC 센서를 윈드실드 브래킷에 고정하는 나사(2개)를 탈거하여 폐기합니다.
참고PH00 Philips, 토크 0.12Nm경고패스너는 크기가 매우 작습니다. 떨어뜨리거나 잃어버리지 않도록 주의하십시오. 올바른 십자 드라이버를 사용했는지 확인하십시오. 드라이버가 너무 크면 나사가 원형 마모됩니다.
-
윈드실드 브래킷에서 윈드실드 HVAC 센서를 탈거합니다.
참고포켓 드라이버를 사용하여 센서를 조심스럽게 들어 올려 접착제에서 폼을 분리합니다.
장착
참고
Ensure that a graphene foam block is present on the contact pad and the blue tape
is removed from the sensor foam pad before installation. If the foam is degraded or
no longer present, install a new graphene foam block. Clean all adhesive
residue that is left from the old foam. The foam is required for conducting the
temperature of the windshield to the sensor.
-
새 윈드실드 HVAC 센서 폼 패드를 배치할 부분을 닦아냅니다.
경고Make sure all adhesive residue from the windshield is removed and the windshield is dry before installation. The foam pad will not stick if the windshield is wet. Align the located hole of the sensor with the plastic alignment pin on the windshield bracket.TIp다음 공구 사용을 권장합니다.
- IPA 천
참고1분간 건조시킵니다. -
윈드실드 브래킷에 윈드실드 HVAC 센서를 장착합니다.
참고PCB의 구멍을 플라스틱 정렬 핀과 맞춥니다.
-
윈드실드 HVAC 센서를 윈드실드 브래킷에 고정하는 새 나사(2개)를 장착합니다.
경고나사가 쉽게 파손되거나 벗겨질 수 있으니 과도한 힘으로 조이지 마십시오.참고PH00 Philips, 토크 0.12Nm참고새 나사를 장착합니다.
-
윈드실드 HVAC 센서 전기 커넥터를 연결합니다.
- 상단 쿼드 카메라 커버를 장착합니다. 참조 항목: 상단 커버 - 리어 뷰 미러(탈거 및 교체).
- 리어 뷰 미러를 장착합니다. 참조 항목: 미러 - 후방(탈거 및 교체).
- 하단 쿼드 카메라 커버를 장착합니다. 참조 항목: 카메라 커버 - 하단(탈거 및 교체).
-
정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드):
UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
- Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
- Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
- Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
- Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
- Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
- Thermal ➜ HVAC ➜ CAN Redeploy
- chassis ➜ DPB Post Replacement ➜ CAN Redeploy
- chassis ➜ ESP Post Replacement ➜ CAN Redeploy
- chassis ➜ IDB Post Replacement ➜ CAN Redeploy
- chassis ➜ RCU Post Replacement ➜ CAN Redeploy
- chassis ➜ ESP Replacement Panel ➜ CAN Redeploy
- chassis ➜ IBST Replacement Panel ➜ CAN Redeploy