교정 코드 21152902 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT에 대한 자세한 내용과 FRT가 만들어진 방법은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.

1. Open LH front door

   

2. Lower LH and RH front windows

   

3. Open RH front door

   

4. Move RH front seat backward

   

5. Open hood
   참고

   Via center display > Controls > Frunk Open

   

   

6. Power off vehicle via center display
   참고

   Controls > Safety & Security > Power Off

   

7. Remove rear underhood apron
   참고

   11x clips, 2x datums

   

   

8. Disconnect LV battery connector and First Responder Loop
   참고

   2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL

   

   

   

9. Remove RH front floor mat

   

10. Remove RH footwell cover
    참고

    3x magnets, 1x connector, 4x datums

    

    

11. Remove RH console side carpet
    참고

    11x clips, 2x datums

    

    

12. Remove RH front door sill trim panel
    참고

    8x clips, 3x datums

    

    

13. Remove RH IP end cap
    참고

    3x clips

    

14. Remove RH mid A-pillar trim
    참고

    2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim

    

    

    

15. Remove RH lower A-pillar trim
    참고

    1x bolt, T25, 5 Nm, 2x clips, 1x datum

    

    

    

16. Fold RH front cabin carpet aside for access

    

17. Release harness from RH footrest panel
    참고

    1x clip

    

18. Release RH footrest panel
    참고

    2x bolts, 10mm, 5 Nm, 2x nut, 10mm, 5 Nm

    

19. Remove RH footrest panel
    참고

    Fold RH primary support carpet up, Rotate RH footrest panel out of vehicle

    

    

20. Release connection at LH side of AP motherboard
    참고

    1x connector, Release antenna connector that crosses in front of car computer cover (Brown connector), Release lock on connector before removal

    

    

21. Release connector to connectivity module
    참고

    1x connector, Move release lock rearward before removal

    

    

22. Put on ESD wrist strap and connect to vehicle ground

    

23. Remove the car computer top cover fasteners
    참고

    9x screws, T10, 1.4 Nm, Discard after removal, Power tools recommend to reduce time required

    

24. Remove car computer cover

    

    

25. Remove the connectivity board mounting screws
    참고

    6x screws, T10, 0.7 Nm, Discard after removal

    

26. Slide the connectivity board down to separate connector and remove
    참고

    1x connector, Ensure full disengagement of connectivity board before attempting to remove

    

    

27. Slide the connectivity board in to the PCB connector
    참고

    1x connector, 1x datum, Align datum with slot in connectivity card and fully engage

    

    

    

28. Install mounting screws to secure connectivity board
    참고

    6x screws, T10, 0.7 Nm, Install new fasteners

    

29. Install car computer cover

    

    

30. Install top cover mounting screws
    참고

    9x screws, T10, 1.4 Nm, Install new screws

    

31. Remove the ESD wrist strap

    

32. Install connector to connectivity module
    참고

    1x connector, Slide lock underneath connector

    

    

33. Install connection at LH side of AP motherboard
    참고

    1x connector

    

    

34. Connect First Responder Loop and LV battery connector
    참고

    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage upper locking tab when fully seated

    

    

35. Install rear underhood apron
    참고

    11x clips, 2x datums

    

    

36. Close hood

    

37. Install RH footrest panel
    참고

    Rotate RH footrest panel onto vehicle, Fold RH primary support carpet down

    

    

38. Secure RH footrest panel
    참고

    2x bolts, 10mm, 5 Nm, 2x nut, 10mm, 5 Nm

    

39. Secure harness to RH footrest panel
    참고

    1x clip

    

40. Fold RH main carpet back into place

    

41. Install RH footwell cover
    참고

    3x magnets, 4x datums, 1x connector

    

    

42. Install RH lower A-pillar trim
    참고

    1x bolt, T25, 5 Nm, 2x clips, 1x datum

    

    

43. Install RH mid A-pillar trim
    참고

    2x clips, 3x datums, Verify weather seal is seated properly

    

    

    

44. Install RH IP end cap
    참고

    3x clips

    

45. Install RH front door sill trim panel
    참고

    8x clips, 3x datums

    

    

46. Install RH front floor mat

    

47. Move RH front seat to original position

    

48. Calibrate RH falcon wing door
    참고

    Hold the upper B-pillar button in the down position to manually calibrate

    

    

49. Raise RH front window

    

50. Close RH front door

    

51. Calibrate LH falcon wing door
    참고

    Hold the upper B-pillar button in the down position to manually calibrate

    

    

52. Raise LH front window

    

53. Close LH front door

    

54. Verify BT, WiFi, and LTE are functioning properly