2026-11-03

Center Console (Remove and Replace)

Código de corrección 1519010012 FRT 0.36 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT asociado reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte para ver prácticas de trabajo seguras.

  • 2026-11-03: Added VCUSB Airwave Actuator Self Test routine.
  • 2024-05-07: Added step for connector removal at RH front side of center console.
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
Equipment:
  • 1060071-00-A Torque Wrench 1/4in Dr Hexagon

Especificaciones de apriete

Table 1. Especificaciones de apriete: Center Console (Remove and Replace)
Descripción Valor de apriete Herramientas recomendadas Reutilizar/Sustituir Notas
Pernos (2 uds.) que fijan la parte trasera de la consola central a la carrocería
7 Nm (5.2 lbs-ft)
  • Vaso de 10 mm
 Reutilizar
Pernos (2 uds.) que fijan la parte delantera izquierda de la consola central a la carrocería
7 Nm (5.2 lbs-ft)
  • Vaso de 10 mm
 Reutilizar
Pernos (2 uds.) que fijan la parte delantera derecha de la consola central a la carrocería
7 Nm (5.2 lbs-ft)
  • Vaso de 10 mm
 Reutilizar

Retirar

  1. Open all the doors and lower all the windows.
  2. Remove the center console rear end panel. See .
  3. Remove the bolts (x2) that attaches the LH and RH rear of the center console to the body.
    Note
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  4. Remove the LH center console front side panel carpet. See .
  5. Remove the bolts (x2) that attach the LH front of the center console to the body.
    Note
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  6. Remove the RH center console front side panel carpet. See .
  7. Remove the bolts (x2) that attach the RH front of the center console to the body.
    Note
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  8. Disconnect the LV power. See .
  9. Disconnect the electrical connector from the rear of the center console.
    Note
    After disconnecting the electrical harness, release the clip that attaches the electrical connector to the center console with a clip prytool.
  10. Remove the harness clip from the RH front side of the center console, and then disconnect the connector.
  11. With an assistant, remove the center console from the vehicle as follows:
    1. Tilt the rear of the center console upwards.
    2. Pull the center console towards the rear of the vehicle.
    3. Tilt the front of the center console upwards.
    4. Remove the center console through the passenger front door.

Instalar

  1. With an assistant, install the center console into the vehicle as follows:
    1. Tilt the front of the center console downwards.
    2. Slide the center console towards the front of the vehicle.
    3. Tilt the rear of the center console downwards until it is in place.
  2. Connect the electrical connector in the rear of the center console.
    Note
    Install the clip that attaches the electrical connector to the center console first and then connect the electrical harness.
    CAUTION
    Ensure the connector is properly installed. Perform a push-pull test before continuing this procedure.
  3. Reconnect the LV power. See .
  4. Install the bolts (x2) that attach the RH front of the center console to the body.
    7 Nm (5.2 lbs-ft)
    Note
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  5. Install the RH center console front side panel carpet. See .
  6. Install the bolts (x2) that attach the LH front of the center console to the body.
    7 Nm (5.2 lbs-ft)
    Note
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  7. Install the LH center console front side panel carpet. See .
  8. Install the bolts (x2) that attaches the LH and RH rear of the center console to the body.
    7 Nm (5.2 lbs-ft)
    Note
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  9. Install the center console rear end panel. See .
  10. Connect a laptop with Toolbox to the vehicle. See .
  11. Reinstall the vehicle firmware. See .
  12. Run the routine: TEST-SELF_VCUSB_X_HVAC-ACTUATORvia Toolbox:(link)
  13. Disconnect the laptop from the vehicle.
  14. Exit Service Mode Plus.
  15. Raise all the windows and close all the doors.