2026-08-05

Valance - Front Fascia (Remove and Replace)

Código de corrección 1203010052 FRT 0.30 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte para ver información sobre prácticas de trabajo seguras.

  • 2026-07-31: Added steps for the super horn cover clip.
  • 2026-03-16: Added notes and tools for bolts securing front valance to front fascia on newer vehicles.
Informational PurposesAn informational icon, calling your attention
Nota
The images in this repair procedure show a Non-Performance vehicle. The instructions apply to both the Non-Performance and the Performance version.

Especificaciones de apriete

Tabla 1. Especificaciones de apriete: Valance - Front Fascia (Remove and Replace)
Descripción Valor de apriete Herramientas recomendadas Reutilizar/Sustituir Notas
Screws (x3) that attach the super horn to the valance
1.8 Nm (1.3 lbs-ft)
  • Vaso Torx T25
 Reutilizar
Bolts (x8) that attach the valance to the fascia
3 Nm (2.2 lbs-ft)
  • Vaso Torx T40
  • (If equipped) Vaso de 10 mm
 Reutilizar
Nuts (x2) at the LH and RH corners of the valance
3 Nm (2.2 lbs-ft)
  • Vaso de 10 mm
 Reutilizar

Retirar

  1. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  2. Remove the push clips (x6) that attach the LH and RH sides of the valance to the wheel arch liners.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the outer clips as necessary to allow for easier access to the nuts behind the wheel liner.
  3. Remove the clip that attaches the super horn cover to the front fascia.
  4. Remove the nuts (x2) at the LH and RH corners of the valance.
    Informational PurposesAn informational icon, calling your attention
    Note
    The nuts are accessed from behind the front of the wheel arch liners.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  5. Release the clip that attaches the super horn harness to the super horn, and then disconnect the super horn connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    El acceso al conector podría variar en función de la versión del altavoz de audio del superclaxon instalada en el vehículo.
  6. Remove the bolts (x8) that attach the valance to the front fascia, and then remove the valance from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Newer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T40
    • (If equipped) Vaso de 10 mm
  7. Remove the screws (x3) that attach the super horn to the valance, and then remove the super horn from the valance.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T25

Instalar

  1. Install the super horn to the valance, and then install the screws (x3) that attach the super horn to the valance.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T25
  2. Install the valance to the front fascia, and install the bolts (x8) that attach the valance to the fascia.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Newer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T40
    • (If equipped) Vaso de 10 mm
  3. Connect the super horn connector, and then install the clip that attaches the super horn harness to the super horn.
  4. Install the nuts (x2) at the LH and RH corners of the valance.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The nuts are accessed from behind the front of the wheel liners.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  5. Install the clip that attaches the super horn cover to the front fascia.
  6. Install the push clips (x6) that attach the LH and RH sides of the valance to the wheel liners.
  7. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).