2026-05-12

Door - Rear - LH (Remove and Install)

Correction code 10106501 0.36 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

Remove

  1. Remove the LH middle A-pillar trim. See .
  2. Remove the LH lower A-pillar trim. See .
  3. Release the clips that attach the LH front seat harness and guide to the body.
  4. Move LH front seat fully forward.
  5. Release the LH upper B-pillar assembly, and then move it aside.
  6. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  7. Remove the LH lower C-pillar trim. See .
  8. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Non-Structural Pack) (Remove and Replace).
  9. Release the clips (x2), grommet and connector for the rear LH door electrical harness seal at the B-pillar, and release the wiring harness from the B-pillar bulkhead.
  10. Pull the rubber grommet through the inside of the LH rear door, and then remove the LH rear door harness from the door assembly.
  11. Remove the bolt that attaches the LH rear door check strap to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
  12. Remove the nuts that attach the LH rear door check strap to the door, and then remove the check strap from the assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm 12-point deep socket
  13. Loosen the bolts that attach the rear LH door to the upper and lower hinges by approximately 5 mm.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  14. With assistance, remove the bolt on the lower hinge, remove the bolt on the upper hinge, and then unhook and lift the door away from the vehicle.

Install

  1. With assistance, position the LH rear door assembly onto the vehicle.
  2. Install and hand-tighten the upper and lower bolts that attach the rear LH door to the upper and lower hinges.
  3. Position the LH rear door check strap onto the door assembly, and then install the nuts that attach the door check strap to the door.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm 12-point deep socket
  4. Install the bolt that attaches the LH rear door check strap to the body.
    24 Nm (17.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
  5. Position the LH rear door harness into the door assembly, and then install the rubber grommet into the inside of the LH rear door.
  6. Install the clips (x2), grommet and connector for the rear LH door electrical harness seal to the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Press the harness connector into the body connector until an audible click is heard.
  7. Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Non-Structural Pack) (Remove and Replace).
  8. Install the LH lower C-pillar trim. See .
  9. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  10. Install the LH upper B-pillar assembly. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  11. Move LH front seat to its original position.
  12. Install the clips that attach the LH front seat harness and guide to the body.
  13. Install the LH lower A-pillar trim. See .
  14. Install the LH middle A-pillar trim. See .
  15. Close the LH rear door and check for gap and flushness. Adjust as necessary.
  16. Open the LH rear door and torque the bolts that attach the door assembly to the upper and lower hinges.
    49 Nm (36.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  17. Calibrate the LH rear window. See .