2026-03-06

帘式气囊 - 右侧(右驾驶) ((拆卸和更换))

校正代码 2001108022 FRT 1.26 注意:除非本程序中另有明确规定,否则上文所列校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅深入了解 FRT 及其创建方式。 注意:请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意:请参阅查看安全健康的作业规程。

  • 2026-02-20: 添加了“如需通过本程序诊断辅助约束系统 (SRS) ,请使用 PROC_RCM_DISARM”的说明。
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
通过执行本程序诊断车辆辅助约束系统 (SRS) 时,为避免任何气囊和预紧器展开,请禁用约束控制模块。重新安装所有车辆辅助约束系统部件后,请重新启用约束控制模块。
  • 禁用约束控制模块:PROC_RCM_DISARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Disarm RCM
    • Safety & Restraints ➜ Seats ➜ Disarm RCM
    via Toolbox:(link)
  • 重新启用约束控制模块:PROC_RCM_ARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Re-Arm RCM
    • Safety & Restraints ➜ Seats ➜ Re-Arm RCM
    via Toolbox:(link)
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
Make sure LV power has been disconnected for at least 2 minutes before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see .
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
Supplementary Restraint System (SRS) components can be hazardous if not handled properly. For more information on SRS precautions, see .

拆卸

  1. 拆卸顶篷。请参阅
  2. 将前排座椅向前移动。
  3. 断开低压电源请参阅
  4. 提起白色锁片,以断开右侧安全气帘电气线束连接器。
  5. 拆卸将右侧安全气帘固定到车身的螺栓(10 个)。
    Informational PurposesAn informational icon, calling your attention
    请勿使用冲击工具拆卸这些自攻螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 无绳棘轮/冲击钻
    • 2 英寸加长件
    • 10 毫米套筒扳手
    • 棘轮/扭矩扳手
  6. 小心松开用于固定右侧安全气帘的卡子(8 个),然后将气囊从车辆上拆下。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    如有任何卡子发生损坏,请更换气囊。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    气囊始终应由点火器操控;切勿让点火器处于悬垂状态。

安装

  1. 将右侧安全气帘安装到纵梁上,然后小心紧固将气囊固定到纵梁的卡子(8 个)。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    如有任何卡子发生损坏,请更换气囊。
  2. 安装并手动拧紧将右侧安全气帘固定到车身的自攻螺栓(10 个)。
    Informational PurposesAn informational icon, calling your attention
    确保调谐器与气囊保持一定距离且二者未相互干涉。
  3. 紧固将右侧安全气帘固定到车身的螺栓(10 个)。
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    请勿使用冲击工具安装自攻螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 无绳棘轮/冲击钻
    • 2 英寸加长件
    • 10 毫米套筒扳手
    • 棘轮/扭矩扳手
  4. 连接右侧安全气帘电气线束连接器。
  5. 连接 12V 电源。请参阅
  6. 将前排座椅向后移动并放倒靠背。
  7. 安装顶篷。请参阅