2026-08-05
下围板 - 前底板 ((拆卸和更换))
校正代码
1203010052
FRT
0.30
注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅深入了解 FRT 及其创建方式。
注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
注意：请参阅查看安全健康的作业规程。
- 2026-07-31: Added steps for the super horn cover clip.
- 2026-03-16: Added notes and tools for bolts securing front valance to front fascia on newer vehicles.
注
The images in this repair procedure show
a Non-Performance vehicle. The instructions apply to both the Non-Performance and the
Performance version.
扭矩规格
| 描述 | 扭矩值 | 推荐工具 | 重复使用/更换 | 备注 |
|---|---|---|---|---|
| Screws (x3) that attach the super horn to the valance |
 1.8 Nm (1.3 lbs-ft) |
|
重复使用 | |
| Bolts (x8) that attach the valance to the fascia |
3 Nm (2.2 lbs-ft) |
|
重复使用 | |
| Nuts (x2) at the LH and RH corners of the valance |
3 Nm (2.2 lbs-ft) |
|
重复使用 |
拆卸
- Remove the front aero shield panel. See 流线型护板 - 前底板 ((拆卸和更换)).
-
Remove the push clips (x6)
that attach the LH and RH sides of the valance to the wheel arch
liners.
NoteRemove the outer clips as necessary to allow for easier access to the nuts behind the wheel liner.
-
Remove the clip that attaches the super horn cover to the front fascia.
-
Remove the nuts (x2) at the
LH and RH corners of the valance.
NoteThe nuts are accessed from behind the front of the wheel arch liners.TIp推荐使用以下工具
- 10 毫米套筒扳手
-
Release the clip that attaches the
super horn harness to the super horn, and then disconnect the super horn
connector.
Note接触连接器的方式可能会因安装在车辆上的超级喇叭音频扬声器版本不同而不同。
-
Remove the bolts (x8) that
attach the valance to the front fascia, and then remove the valance from the
vehicle.
NoteNewer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.TIp推荐使用以下工具
- 梅花 T40 套筒
- (If equipped) 10 毫米套筒扳手
-
Remove the screws (x3) that attach the
super horn to the valance, and then remove the super horn from the valance.
TIp推荐使用以下工具
- T25 梅花套筒
安装
-
Install the super horn to the valance,
and then install the screws (x3) that attach the super horn to the valance.1.8 Nm (1.3 lbs-ft)TIp推荐使用以下工具
- T25 梅花套筒
-
Install the valance to the
front fascia, and install the bolts (x8) that attach the valance to the
fascia.3 Nm (2.2 lbs-ft)NoteNewer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.TIp推荐使用以下工具
- 梅花 T40 套筒
- (If equipped) 10 毫米套筒扳手
-
Connect the super horn connector, and
then install the clip that attaches the super horn harness to the super horn.
-
Install the nuts (x2) at the
LH and RH corners of the valance.3 Nm (2.2 lbs-ft)NoteThe nuts are accessed from behind the front of the wheel liners.TIp推荐使用以下工具
- 10 毫米套筒扳手
-
Install the clip that attaches the super horn cover to the front fascia.
-
Install the push clips (x6)
that attach the LH and RH sides of the valance to the wheel liners.
- Install the front aero shield panel. See 流线型护板 - 前底板 ((拆卸和更换)).