2026-05-12

Seat Back - 2nd Row - LH (Remove and Replace)

Correction code 13054002 0.30 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

  • 2024-07-23: Deleted the seatback cushion separation steps.
  • 2024-08-15: Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.
Equipamento:
  • Torchless Heat Induction Tool - 2152873-00-A

Torque Specifications

Tabela 1. Torque Specifications: Seat Back - 2nd Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x5) that attach the LH 2nd row seat back frame to the vehicle
37 Nm (27.3 lbs-ft)
  • 11 mm socket
Replace
Warning IconA warning icon, calling your attention to a possibly risky situation
CUIDADO
Bolts must be installed in the following sequence:
  1. Front Outboard
  2. Rear Inboard
  3. Rear Outboard
  4. Front Inboard

Remove

  1. Remove the LH lower C-pillar trim. See .
  2. Release the clips (x3) that attach the main carpet to the lower seat cushion frames.
  3. Remove the bolts (x5) that attach the LH 2nd row seat back frame to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The two frontmost bolts are behind the main carpet.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 11 mm socket
  4. Carefully fold down the LH 2nd row seat back.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CUIDADO
    Place a protective covering on the seat back upholstery and take care not to damage the upholstery during removal of the seat back.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CUIDADO
    Do not place any additional weight on the seat back. Doing so may damage the seat frame alignment tabs, which can cause unevenness between the 60 and 40 seat backs.
  5. Disconnect the electrical harness from the connector at the LH lower seat frame.
  6. With assistance, carefully remove the LH 2nd row seat back assembly from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CUIDADO
    Place the seat back assembly in an area where it will not be tipped over or otherwise damaged.
    Informational PurposesAn informational icon, calling your attention
    Nota
    For NA only: If the 2nd row seat that is not being replaced does not have ISOFIX flag for child locks, replace the seat cover.. See .

Install

  1. With assistance, position the LH 2nd row seatback assembly into place, and then connect the electrical harness to the connector at the LH lower seat frame.
  2. Move the LH 2nd row seatback to vertical position.
  3. Install the bolts (x5) that attach the LH 2nd row seat back frame to the vehicle.
    37 Nm (27.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The two frontmost bolts are behind the main carpet.
    Informational PurposesAn informational icon, calling your attention
    Note
    Torque in the sequence of:
    1. Front Outboard
    2. Rear Inboard
    3. Rear Outboard
    4. Front Inboard
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 11 mm socket
  4. Install the clips (x3) that attach the main carpet to the lower seat cushion frames.
  5. Install the LH lower C-pillar trim. See .