2026-05-12

Ankle Catcher (Remove and Replace)

Correction code 10011202 0.60 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
The corners of the ankle catcher are very sharp and might cause personal injury. When performing this procedure, make sure wearing proper PPE and pay attention to the sharp edges.

Torque Specifications

Tabela 1. Torque Specifications: Ankle Catcher (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the front bumper beam to the ankle catcher
16 Nm (11.8 lbs-ft)
  • 13 mm socket
 Reuse
Bolts that attach the front end carrier to the LH subframe crash cans
16 Nm (11.8 lbs-ft)
  • 13 mm socket
 Reuse
Bolt that attaches the front end carrier to the LH side of the ankle catcher
7 Nm (5.2 lbs-ft)
  • 13 mm socket
 Reuse

Remove

  1. Remove the front fascia. See Fascia - Front (Remove and Install).
  2. Remove the bolt that attaches the front bumper beam to the RH side of the ankle catcher.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  3. Remove the bolts that attach the front end carrier to the RH subframe crash cans.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Remove the bolt that attaches the front end carrier to the RH side of the ankle catcher.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  5. Repeat step 2 through step 4 for the LH side of the vehicle.
  6. Slightly pull the front end carrier away from the ankle catcher, and then rotate the rear of the ankle catcher downward and toward the front of the vehicle to remove it.

Install

  1. Slightly pull the front end carrier away from the ankle catcher, and then position the ankle catch on the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Rotate the rear of the ankle catcher up and toward the rear of the vehicle.
  2. Install the bolts that attach the front bumper beam to the ankle catcher.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  3. Install the bolts that attach the front end carrier to the LH subframe crash cans.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Install the bolt that attaches the front end carrier to the LH side of the ankle catcher.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  5. Repeat steps 3 and step 4 for the RH side of the vehicle.
  6. Install the front fascia. See Fascia - Front (Remove and Install).