2024-08-01

IP Carrier (Remove and Replace)

Correction code 14052102 1.98 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

  • 2023-03-29: Revised procedure.
  • 2024-01-29: Re-structured the procedure.
  • 2024-07-30: Added information about how to handle the replacement between different versions of IP carrier.
Table 1. Torque Specifications: IP Carrier (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH and RH window defroster ducts to the instrument panel carrier
2.3 Nm (1.7 lbs-ft)
  • Torx T20 socket
  • 2 in extension
  • Ratchet/torque wrench
Reuse

Remove

  1. Remove the instrument panel carrier. See .
  2. Remove the front passenger air bag. See .
  3. Remove the bolts (x2) that attach the LH and RH window defroster ducts to the instrument panel carrier, and remove the ducts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  4. Remove the LH and RH defrost covers. See .
    Informational PurposesAn informational icon, calling your attention
    Note
    4 tabs for the LH side and 5 tabs for the RH side.

Install

  1. If the new instrument panel carrier does not have tweeter holes, the tweeter connectors must be taped back to the harness before the replacement instrument panel carrier is installed.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do NOT cut holes into the new instrument panel carrier as an attempt to retrofit the tweeters.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Failure to tape back the existing tweeter connector may result in NVH issues.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use black tape. The yellow tape used in the picture is for demonstration purpose only.
  2. If the new instrument panel carrier has tweeter holes while the replaced one does not, the tweeter hole must be covered before the replacement instrument panel carrier is installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Cut a piece of butyl to cover the hole. Make sure the butyl does not cover the IP clips or interfere with the speaker perimeter.
  3. Install the LH and RH defrost covers. See .
    Informational PurposesAn informational icon, calling your attention
    Note
    4 tabs for the LH side and 5 tabs for the RH side.
  4. Install the bolts (x2) that attach the LH and RH window defroster ducts to the instrument panel carrier.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  5. Install the front passenger air bag. See .
  6. Install the instrument panel carrier. See .