2026-05-12

Brake Pedal (Non-Structural Pack) (Remove and Replace)

Correction code 33251002 2.94 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

  • 2025-09-08: Added steps to remove/install the cross car beam from/to the vehicle.

Remove

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  3. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  4. Remove the cross car beam. See Beam - Cross Car (Remove and Replace)
  5. Disconnect the brake pedal electrical connector.
  6. Remove the brake light switch. See #GUID-DE004FA8-A2D6-4E84-B56B-E8CF8BD20DB5.
  7. Remove the brake clevis pin cotter pin.
  8. Remove the brake clevis pin that attaches the brake pedal to the electromechanical brake booster.
  9. Disconnect the accelerator pedal electrical connector.
  10. Release the clips that attach the electrical harness to the brake pedal assembly.
  11. Remove the bolt and discard the nuts (x4) that attach the brake pedal assembly to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm socket
    • 10mm socket
    • Flex head ratchet / flex head torque wrench
    • 6 in extension
  12. Remove the brake pedal and the accelerator pedal as an assembly from the vehicle.

Install

  1. Install the brake pedal assembly onto the studs (x4) of the body.
  2. Install the bolt and new nuts (x4) that attach the brake pedal assembly to the vehicle.
    16.5 Nm (12.2 lbs-ft)
    13 Nm (9.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm socket
    • 10mm socket
    • Flex head ratchet / flex head torque wrench
    • 6 in extension
  3. Fasten the clips that attach the electrical harness to the brake pedal assembly.
  4. Connect the accelerator pedal electrical connector.
  5. Install the brake clevis pin that attaches the brake pedal to the electromechanical brake booster.
  6. Install the brake clevis pin cotter pin.
  7. Install the brake light switch. See #GUID-DE004FA8-A2D6-4E84-B56B-E8CF8BD20DB5.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install a new brake switch if the existing one was damaged during removal.
    Informational PurposesAn informational icon, calling your attention
    Note
    Confirm that the brake pedal is in the home position: Push the brake pedal switch into the clip until it stops, and then twist the brake switch clockwise 45 degrees to set the brake switch in position. Do not push the brake pedal switch too hard as to move the brake pedal.
  8. Connect the brake pedal electrical connector.
  9. Install the cross car beam. See Beam - Cross Car (Remove and Replace)
  10. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  11. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  12. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).