2026-11-09

Door Assembly - Rear - LH (Remove and Replace)

Correction code 10106202 1.38 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2026-11-09: Added steps for left over clip retainers and references for the panel alignment procedure.
  • 2026-02-23: Added step to disconnect LV power before disconnecting the door pressure sensor electrical connector.

Remove

  1. Remove the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  2. Remove the left over clip retainers from the rear door.
    Note
    The number of the retainers may vary.
  3. Remove the bolts (x2) that attach the LH rear door grab handle to the door assembly, and then remove the grab handle from the door.
    Tip
    Use of the following tool(s) is recommended:
    • 8 mm socket
  4. Remove the butyl patches that cover the LH rear door regulator isolator clamps.
  5. Remove plugs (x2) that cover the openings in LH rear door to access the LH rear door regulator mounting guides.
  6. Connect the window switch special tool to the LH rear door harness.
  7. Pull the white tab to release the connector lock, and then disconnect the LH rear door handle controller electrical connector.
  8. Disconnect the LH rear door pressure sensor electrical connector.
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  9. Remove the bolts (x6) that attach the LH rear door closeout panel to the door assembly.
    Tip
    Use of the following tool(s) is recommended:
    • 8 mm socket
  10. Release the clips (x3) that attach the wiring harness to the LH rear door closeout panel, and then remove the closeout panel from the vehicle.
    Note
    Release the clips from the back of panel to prevent damage.
  11. Remove the LH rear door speaker. See Speaker - Rear Door - LH (Remove and Replace).
  12. Use the window switch special tool to raise the LH rear door glass partially for access to the foremost regulator isolator clamp.
  13. Release the LH C-pillar margin seal from the LH rear door assembly, and then remove the seal from the assembly.
  14. Release the LH rear door margin seal from the LH rear door assembly, and then remove the seal from the assembly.
  15. Release the clips (x11) that attach the LH rear door seal to the door assembly, and then remove the seal from the assembly.
  16. Remove the LH B-pillar margin rear door seal. See Seal - Door - Rear - Margin - B Pillar - LH (Remove and Replace).
  17. Remove the LH rear door glass. See .
  18. Remove the LH rear window regulator. See .
  19. Remove the LH rear door harness. See .
  20. Remove the LH rear exterior release door handle assembly. See .
  21. Remove the bolts (x2) that attach the LH rear door striker to the LH rear door, and then remove the striker from the door.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T40 socket
  22. With an assistant supporting the door, remove the hinge bolts (x4) that attach the LH rear door to the vehicle, and then remove the door from the vehicle.
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket

Install

CAUTION
If using this procedure to install an unpainted part, make sure to apply seam sealer to all seams prior to installing and painting the part. Refer to the Collision Repair manual for more information.
  1. With an assistant, position the LH rear door onto the vehicle, and then install the hinge bolts (x4) that attach the door to the vehicle.
    24 Nm (17.7 lbs-ft)
    Note
    Adjust alignment as necessary before tightening the bolts.
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  2. Position the LH rear door striker to the LH rear door, and then install the bolts (x2) that attach the striker to the door.
    22 Nm (16.2 lbs-ft)
    Note
    Adjust alignment as necessary before tightening the bolts.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T40 socket
  3. Install the LH rear exterior release door handle assembly. See .
  4. Install the LH rear door harness. See .
  5. Install the LH rear window regulator. See .
  6. Remove the LH rear door glass. See .
  7. Remove the LH B-pillar margin rear door seal. See Seal - Door - Rear - Margin - B Pillar - LH (Remove and Replace).
  8. Install the LH rear door inner belt seal. See Seal - Inner Belt - Rear Door - LH (Remove and Replace).
  9. Install the LH B-pillar margin rear door seal. See Seal - Door - Rear - Margin - B Pillar - LH (Remove and Replace).
  10. Position the LH rear door seal onto the door assembly, and then fasten the clips (x11) that attach the to the door assembly.
  11. Install the LH C-pillar margin seal onto the LH rear door assembly.
  12. Install the LH rear door margin seal onto the LH rear door assembly.
  13. Install the LH rear door speaker. See Speaker - Rear Door - LH (Remove and Replace).
  14. Position the LH rear door closeout panel onto the door, and then install the bolts (x6) that attach the closeout panel to the door..
    4 Nm (2.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 8 mm socket
  15. Install the clips (x3) that attach the wiring harness onto the LH rear door closeout panel.
  16. Connect the LH rear door pressure sensor electrical connector, and then engage the connector lock.
  17. Connect the LH rear door handle controller electrical connector, and then engage the connector lock.
  18. Raise the LH rear window fully.
  19. Close the LH rear door.
  20. Check gap and flushness on the LH rear door.
    Note
  21. Check the gap between the LH rear window and LH B-pillar applique.
    Note
  22. Adjust the LH rear door to specification as necessary.
    Note
    Loosen the hinge and striker bolts to make adjustments. Torque the bolts after alignment.
    Note
    Window and door adjustment may need to be done simultaneously in order to ensure proper closure.
  23. Lower the LH rear window partially to access the rearmost regulator isolator clamp.
  24. Loosen the rearmost bolt that attaches the LH rear door glass to the regulator isolator clamp enough to maintain glass position but still allow for adjustment.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  25. Lower the LH rear window partially to access the rearmost regulator isolator clamp.
  26. Loosen the foremost bolt that attaches the LH rear door glass to the regulator isolator clamp enough to maintain glass position but still allow for adjustment.
    8 Nm (5.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  27. Adjust the LH rear door glass to achieve gap target, and then hand tighten foremost bolt.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  28. Raise the LH rear window partially to access the rearmost regulator isolator clamp.
  29. Adjust the LH rear door glass to achieve gap target, and then hand tighten rearmost bolt.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  30. Raise the LH rear window fully and close the LH rear door.
  31. Check the gap between the LH rear window and LH B-pillar applique.
    Note
  32. Check gap and flushness on the LH rear door.
    Note
  33. Open the LH rear door.
  34. Lower the LH rear window partially to access the rearmost regulator isolator clamp.
  35. Torque bolt that attaches the LH rear door glass to the regulator rearmost isolator clamp.
    8 Nm (5.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  36. Lower the LH rear door glass partially for access to foremost regulator isolator clamp.
  37. Torque the bolt that attaches the LH rear door glass to the foremost regulator isolator clamp.
    8 Nm (5.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  38. Raise the window fully.
  39. Close the LH rear door.
  40. Check the flushness between the LH rear door glass and LH B-pillar applique.
    Note
  41. Open the LH rear door.
  42. Loosen the lower LH rear regulator mounting nuts (x2) enough to maintain position but still allow adjustment.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  43. With assistance, adjust the LH rear door glass to achieve flushness target, and then hand tighten the lower LH rear regulator mounting nuts (x2).
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  44. Close the LH rear door.
  45. Check the flushness between the LH rear door glass and LH B-pillar applique.
    Note
  46. Open the LH rear door.
  47. Torque the lower LH rear regulator mounting nuts (x2).
    10 Nm (7.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  48. Lower the LH rear window fully.
  49. Disconnect the window switch special tool.
  50. Install plugs (x2) that cover the openings in LH rear door.
  51. Install the butyl patches that cover the openings in the LH rear door.
  52. Position the LH rear door grab handle onto the door assembly, and then install the bolts that attach the grab handle to the door.
    Tip
    Use of the following tool(s) is recommended:
    • 8 mm socket
  53. Install the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  54. Connect a laptop with Toolbox to the vehicle.
  55. In Toolbox, click the Actions/Autodiag tab, and then search for "window".
  56. Click TEST-SELF_VCLEFT_REAR-L_CALIBRATE-WINDOWvia Toolbox:(link), and then click Run and allow the routine to complete.
    Note
    Click ‘X’ at top right of the window to close once complete.
  57. Press LH rear window switch down to second position to activate the auto-lower function, then raise window switch up to second position to activate auto-raise function.
    Note
    If window does not lower completely, repeat previous calibration steps.
  58. Disconnect Toolbox from the vehicle.