2026-07-15

Wiper Module (Remove and Replace)

校正代码 17502502 0.36 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。 注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。注意：请参阅查看安全健康的作业规程。

  • 2026-05-13: Added warning about pinch points on wiper module.
  • 2024-04-04: Added post replacement instructions.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
本程序所含视频仅作为补充材料予以概括说明。请遵循本程序所列的所有步骤，以避免部件损坏和/或人身伤害。

扭矩规格

Table 1. 扭矩规格: Wiper Module (Remove and Replace)
描述 扭矩值 推荐工具 重复使用/更换 备注
Bolts that attach the wiper module to the vehicle
7 Nm (5.2 lbs-ft)
  • 10 mm socket
 重复使用

拆卸

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Remove the cabin intake duct. See 槽 - 上部 - 驾驶室进气（拆卸和更换）.
  3. Right-Hand Drive (RHD) only: Remove the outer HVAC plenum duct. See 气室 - 入口 - HVAC（拆卸和更换）.
  4. Remove the hood latch cover. See Cover - Hood Latch (Remove and Replace).
  5. Remove the underhood storage carpet. See #GUID-3E0628D6-80C0-4137-A533-64C34E3F765C.
  6. Remove the underhood storage unit. See .
  7. Remove the wiper arms. See #GUID-40F2AE79-B55A-4796-B733-9622D9A5F73B.
    Informational PurposesAn informational icon, calling your attention
    Note
    For cars built on or after March 9th, 2019, the wiper module assembly does not have pigtail. Switch to "Wiper Service Mode" when removing it (China only).
  8. Release the clips that attach the LH and RH shock tower covers to the vehicle, and then remove the covers from the vehicle.

    LH shock tower cover shown, RH similar

  9. Release the clips that attach the cowl screen to the vehicle, and then remove the cowl screen from the vehicle.
  10. Disconnect the electrical connector from the wiper module.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Do not place limbs within the module linkage area as the wiper arms will automatically transition to Parking Mode.
  11. Remove the bolts that attach the wiper module to the body, and then remove the wiper module from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    推荐使用以下工具
    • 10 mm socket
    Figure 1. Left-Hand Drive (LHD)
    Figure 2. RHD

安装

  1. Install the bolts that attach the wiper module to the vehicle.
    7 Nm (5.2 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Keep your fingers away from any potential pinch points and moving parts while connecting and installing the wiper module. Do not attempt to test the module until it is fully installed in the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    推荐使用以下工具
    • 10 mm socket
    Figure 3. LHD
    Figure 4. RHD
  2. Connect the electrical connector to the wiper module.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Do not place limbs within the module linkage area as the wiper arms will automatically transition to Parking Mode.
  3. Connect the clips that attach the cowl screen to the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully install the cowl screen panel to avoid damage to the windshield. Applying excessive force on the windshield can crack the glass.
  4. Connect the clips that attach the LH and RH shock tower covers to the vehicle.

    LH shock tower cover shown, RH similar

  5. Install the wiper arms. See #GUID-40F2AE79-B55A-4796-B733-9622D9A5F73B.
  6. Install the underhood storage unit. See .
  7. Install the underhood storage carpet. See #GUID-3E0628D6-80C0-4137-A533-64C34E3F765C.
  8. Install the hood latch cover. See Cover - Hood Latch (Remove and Replace).
  9. Right-Hand Drive (RHD) only: Install the outer HVAC plenum duct. See 气室 - 入口 - HVAC（拆卸和更换）.
  10. Install the cabin intake duct. See 槽 - 上部 - 驾驶室进气（拆卸和更换）.
  11. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  12. Enable Service Mode through the touchscreen. See .
  13. Perform a software reinstall. See .
  14. Run the Wiper Replacement procedure: on the touch screen, touch Service > Closures > Windows > Wiper replacement, touch Run, and allow the routine to complete.
  15. Verify the operation of the windshield washers and wipers.