2024-07-17

灯罐总成

Parts List

Quantity Description Image / Notes
1 M3 ASY, LAMP CAN（灯罐总成）
Informational PurposesAn informational icon, calling your attention
注
更换 LH 组件时： 车辆上的 LH 尾灯是 Tesla 零件号 1077397-00 版本 F（或更低），也请使用 Tesla 零件号 1077397-00 版本 G（或更高）更换 LH 尾灯。
5. Rivet, 4.8 mm
1 Flow Form Rivet S18
1 Flow Form Rivet S08

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Left-hand component only: 拆下充电端口外壳总成。
  2. Remove the original component.
    Informational PurposesAn informational icon, calling your attention
    注
    下图圈注部分显示部分 RH 组件。

    or Factory SPRs

    or Factory Spot Welds

  3. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    注
    下图圈注部分显示部分 RH 组件。

    or Installation Spot Welds

    or Steel Plug Welds
    • A = 7 毫米
    • B = 20 毫米

    or Rivets, 4.8 mm

    or Flow Form Rivets, S08

    or Flow Form Rivets, S18

  4. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  5. Install the new component or components.
  6. Perform resistance spot welding.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
  7. Perform GMA welding.

    or Steel Plug Welds

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    注
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  8. Left-hand component only: 安装充电端口外壳总成。
  9. Perform any necessary post-repair operations.