2025-03-14

后节点(整体)

Parts List

Quantity Description Image / Notes
1 ASSEMBLY - REAR FRAMERAIL COMPLETE(后节点 - 整体)
12 High Strength Structural Rivet, 6.5 mm
17 Structural Bulb Rivet, 6.5 mm
4 Countersunk Rivet, 4.8 mm Long
2 Structural Countersunk Rivet, 6.5 mm
1 Structural Rivet, 6.5 mm Medium
2 Rivet, 4.8 mm
4 Countersunk Rivet, 4.8 mm Short
13 Flow Form Rivet S18
1 Flow Form Rivet S08
2 Flow Form Rivet S28
10 Flow Form Rivet S38
2 螺栓,六角头,BOLT & WSHR, HX, M8x23.5,STL[109],PTC,ZNNI Tesla 零件号 1063260-00-C。

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆卸后车架纵梁端板
  2. 拆卸行李箱底板总成(整体)
  3. 拆卸后电机罩底板
  4. 拆卸后副框架下部横梁
  5. 拆卸第三排座椅横梁(下部)
  6. 拆卸踵板横梁
  7. 拆下车身侧外件的必要部分,露出要更换的底层组件。
  8. Remove the original component.

    or Factory Spot Welds

    or Drill through factory spot welds
    Informational PurposesAn informational icon, calling your attention
    When drilling out spot welds, use a drill bit that creates a hole correctly sized for the fastener that will replace the spot weld.

    or Factory SPRs

    or Bolts

  9. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    A red X indicates a location where a factory-installed fastener is not being replaced.

    or High Strength Structural Rivets, 6.5 mm

    or Structural Bulb Rivets, 6.5 mm
    • A = 12 毫米。
    • B = 10 毫米。

    or Structural Countersunk Rivets, 6.5 mm

    or Countersunk Rivets, 4.8 mm Short

    or Countersunk Rivets, 4.8 mm Long

    or Rivets, 4.8 mm

    or Structural Rivets, 6.5 mm Medium

    or Bolts

    GMA Weld
    Informational PurposesAn informational icon, calling your attention
    每处 GMA 焊缝为 20 毫米长。
  10. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  11. Install the new component or components.

    将这些六角头螺栓拧紧至 24 Nm。

  12. Perform GMA welding.
    GMA Weld
    Informational PurposesAn informational icon, calling your attention
    每处 GMA 焊缝为 20 毫米长。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  13. 安装踵板横梁
  14. Install the fasteners as indicated.
  15. 安装先前为露出更换组件而拆下的车身侧外件部分。。
  16. Install the fasteners as indicated.
  17. 安装第三排座椅横梁(下部)
  18. 安装后副框架下部横梁
  19. 安装后车架纵梁端板
  20. 安装新后车身面板
  21. Perform any necessary post-repair operations.