2024-07-10
充电端口外壳总成
Repair Information
- Review all collision repair general practices and safety documentation and wear the appropriate PPE (Personal Protective Equipment) before beginning this procedure.
- This procedure can be completed without using a frame bench.
Parts List
Quantity | Description | Image / Notes |
---|---|---|
1 | M3 CHARGE PORT HOUSING ASSY SVC(充电端口外壳支架) |
![]() |
1 |
![]() |
Tesla 零件号 1038174-00-A。 注 需要条件:仅当车辆使用防松螺母将接地线连接到充电端口外壳总成时。 |
When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.
Repair Procedure
- Remove the original component.
-
Prepare for installation.
注如果原装组件最初在红色圈示位置配有防松螺母,请务必于该位置安装一个防松螺母。
-
在充电端口外壳支架与围板外壳和原厂泡沫隔板(黄色所示)直接接触的区域涂抹接缝密封剂。
警告本程序要求接缝密封剂的凝固延展率高于 150%。这可避免围板外表面——充电端口外壳支架粘合到面板内侧的位置——出现肉眼可见的变形。警告如果使用的接缝密封剂不适用于裸露金属表面,那么围板内侧的接合面首先需要进行表面修整,再安装充电端口外壳总成。请参阅所使用的接缝密封剂的技术数据表。
- Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
-
Install the new component or components.
注如需要,请安装防松螺母。
-
Perform resistance spot
welding.
or
Installation Spot Welds
警告Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.警告Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components. -
Perform GMA welding.
or
Steel Plug Welds
警告Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.警告To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.警告Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.注Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint. -
安装防松螺母后,请使用万用表检查防松螺母和充电端口外壳之间的连续性。
注电阻不得超过 0.2mΩ。
- Perform any necessary post-repair operations.