2023-10-17

Bracket - B-Pillar - LH (Remove and Replace)

Correction code 1518010112 FRT 0.78 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See for safe and healthy working practices.

Torque Specifications

Table 1. Torque Specifications: Bracket - B-Pillar - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH curtain airbag to the body
9 Nm (6.6 lbs-ft)
  • 10 mm socket
 Reuse
Bolts (x2) that attach the LH B-pillar bracket to the body
2.5 Nm (1.8 lbs-ft)
  • 10 mm socket
 Reuse

Remove

  1. Remove the 2nd row lower seat cushion. See .
  2. Remove the LH side rail trim. See .
  3. Remove the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  4. Remove the LH IP end cap. See .
  5. Remove the LH lower A-pillar trim. See .
  6. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  7. Remove the LH middle B-pillar trim. See Trim - B-Pillar - Middle - LH (Remove and Replace).
  8. Remove the LH upper B-pillar trim. See .
  9. Repeat step 2 through step 8 on the RH side of the vehicle.
  10. Release the rear headliner. See .
  11. Use a pry tool to remove the fir tree clip that attaches the curtain airbag to the B-pillar bracket, then release the LH curtain airbag from the B-pillar bracket.
  12. Remove the bolts (x2) that attach the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Inspect the bolts for captive washers and make sure they are intact with the curtain airbag, if not, replace the curtain airbag.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  13. Remove the bolts (x2) that attach the LH B-pillar bracket to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  14. Use a pry tool to remove the LH B-pillar bracket from the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Install

  1. Position the LH B-pillar bracket onto the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  2. Install the bolts (x2) that attach the LH B-pillar bracket to the body.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the fir tree clip that attaches the curtain airbag to the B-pillar bracket.
  4. Install the bolts (x2) that attach the LH curtain airbag to the body.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply Loctite 222 to the threads of each bolt prior to installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Install the rear headliner. See .
  6. Install the LH upper B-pillar trim. See .
  7. Install the LH middle B-pillar trim. See Trim - B-Pillar - Middle - LH (Remove and Replace).
  8. Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  9. Install the LH lower A-pillar trim. See .
  10. Install the LH IP end cap. See .
  11. Install the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  12. Install the LH side rail trim. See .
  13. Repeat step 6 through step 12 on the RH side of the vehicle.
  14. Install the 2nd row lower seat cushion. See .