Approved Frame Bench Systems and Optional Electronic Measuring Systems
Lists the approved frame bench systems and the optional electronic measuring systems for use when repairing Tesla vehicles.
Frame Bench Systems
The following approved frame bench system companies work closely with the Tesla Body Repair Program to design and build fixtures to Tesla’s exact specifications. This collaboration not only provides accurate component location, but also ensures safe and proper support of the body structure during the repair process.
Note
Some structural repairs on Tesla
vehicles must be performed with the vehicle properly mounted to an approved frame
bench. When a frame bench is to be used for a particular structural repair, the
Repair Information section of the repair procedure indicates to perform the repair
using a frame bench. The electronic measuring systems listed in Optional Electronic Measuring Systems can be used for damage analysis,
but are not a substitute for component fixturing during structural repair.
Note
Frame bench data sheets can be
obtained from the frame bench manufacturer or an authorized distributor.
Note
Use only approved frame bench
systems when repairing Tesla vehicles.
Note
When performing a repair using a
frame bench, use a minimum of 8 control points to the frame bench.
Manufacturer | Approved Equipment | Approved for |
---|---|---|
Car Bench | Frame Benches | |
Manta repair benches 160AA154/5150/F/R |
|
|
Meg | Cybertruck | |
Muraena repair benches AA265/5150/F/R |
|
|
Necessary Frame Bench Accessories | ||
EVO Universal Jig Set |
|
|
Model-specific mini jigs |
|
|
Car-O-Liner | Frame Benches | |
B16 BenchRack BR5000: Part 34639 |
|
|
B81 BenchRack BR4200: Part 34573 |
|
|
B83 BenchRack BR5500: Part 34640 |
|
|
B84 BenchRack BR6300: Part 33907 |
|
|
Q42 Base Frame with Lift: Part 39748 |
|
|
Q42 Base Frame with Lift: Part 40204 |
|
|
Q42 Bench 220V 1ph 60Hz: Part 42111 |
|
|
Necessary Frame Bench Accessories | ||
One of the Car-O-Liner electronic measuring systems listed in the Optional Electronic Measuring Systems section of this document |
|
|
EVO1 basic anchoring system: Part 35413 |
|
|
EVO2 extended anchoring system: Part 35419 |
|
|
EVO3 holding and fixturing system: Part 35719 |
|
|
Celette | Frame Benches | |
Griffon EVO 2.8T Drive-On Bench with Dual Lifts |
|
|
Griffon XL Drive-On Bench w/ 2 Internal Lifts |
|
|
RHÔNE 2.8T Drive-On Bench w/Puller |
|
|
RHÔNE L 2.8T Drive-On Bench |
|
|
RHÔNE L 4.2T Drive-On Bench w/Puller |
|
|
RHÔNE XL |
|
|
Sevenne Bench on Wheels |
|
|
Sevenne XL Bench on Wheels |
|
|
Smart RHÔNE Bench |
|
|
Necessary Frame Bench Accessories | ||
Model-specific upper and lower body fixtures |
|
|
Cameleon Adaptable Jig Set for all Models |
|
|
Chief | Frame Benches | |
Goliath |
|
|
E-VHT 18’ |
|
|
E-VHT 20’ |
|
|
Impulse (Tilt) 18’ |
|
|
Impulse (Tilt) 20’ |
|
|
Phoenix |
|
|
S21 and S21M |
|
|
Titan |
|
|
Excelerator |
|
|
EZ Liner Classic |
|
|
Necessary Frame Bench Accessories | ||
One of the Chief electronic measuring systems listed in the Optional Electronic Measuring Systems section of this document |
|
|
All Brand Base kit: CK300021 |
|
|
Tesla Brand Kit: CK300020 |
|
|
Model Y holding system: CK300034 |
|
|
EV Kit complete: CK140124 |
|
|
EV Kit upgrade: CK140125 |
|
|
Globaljig | Frame Benches | |
5.0 Mobile System |
|
|
5.0 Super Rotax |
|
|
6.0 Super Rotax |
|
|
Evolution 5.0 |
|
|
Necessary Frame Bench Accessories | ||
Universal Fixture System |
|
|
Model-specific mini fixtures |
|
|
Spanesi | Frame Benches | |
106 Bench |
|
|
106 EXT Bench |
|
|
Daytona |
|
|
Pista Bench |
|
|
Necessary Frame Bench Accessories | ||
Superstar Universal Jig System |
|
|
Touch electronic measuring system |
|
|
Universal upper body system |
|
Electronic Measuring Systems
Electronic measuring systems from the manufacturers listed below can be
used when performing damage analysis and structural repairs. The use of these
electronic measuring systems is optional, unless specified otherwise by the frame
bench manufacturer.
Note
Electronic
measuring systems can be used for damage analysis, but are not a substitute for
component fixturing during structural repair.
Manufacturer | Electronic Measuring Systems | Notes |
---|---|---|
Car Bench | Contact Evolution AA250 | Can be used as a stand-alone measuring system. |
Car-O-Liner | Car-O-Tronic Classic First Generation | Used in conjunction with an
approved Car-O-Liner frame bench. Supported M21, M22,
and M23 measuring bridges:
|
Car-O-Tronic M21 + Vision2 X1 Note Does not support
the EVO1, EVO2, or the EVO3 anchoring/fixturing
systems. |
||
Car-O-Tronic M22 + Vision2 X2 Note Does not support
the EVO1, EVO2, or the EVO3 anchoring/fixturing
systems. |
||
Car-O-Tronic M23 + Vision2
X3s Note Supports the EVO1, EVO2, and EVO3 anchoring/fixturing
systems. |
||
Celette | Naja 3D Computerized Electronic Measuring System |
Can be used as a stand-alone measuring system. 12-month data subscription, laptop, and 2 NAJA batteries included. |
Chief | Laser Lock | Used in conjunction with an approved Chief frame bench. |
Laser Lock Align | ||
Meridian Live Mapping System 788LNE81L | ||
Vector | ||
Velocity | ||
Globaljig | GlobalSCAN | Used in conjunction with an approved Globaljig frame bench. |
Spanesi | Touch | Can be used as a stand-alone measuring system. |