2026-05-04

挡泥板总成 - 前 - 左侧（拆卸和安装）

校正代码 101030010.90 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。 注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。注意：请参阅查看安全健康的作业规程。

    This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

    拆卸

    1. Raise and support the vehicle. See 举升车辆 - 双柱举升机.
    2. Remove the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
    3. Remove the cabin intake duct. See 槽 - 上部 - 驾驶室进气（拆卸和更换）.
    4. Remove the hood latch cover. See 盖板 - 前备箱盖闩锁（拆卸和更换）.
    5. Remove the underhood storage unit. See .
    6. Remove the LH shock tower cover. See 盖板 - 减震塔 - 左侧（拆卸和更换）.
    7. Remove the front wheels. See 轮毂总成（拆卸和安装）.
    8. Remove the front aero shield panel. See 面板 - 流线型护板 - 前（拆卸和更换）.
    9. Remove the front fascia. See 饰板 - 前（拆卸和安装）.
    10. Remove the LH headlight. See .
    11. Disconnect the electrical connectors (2x) from the front side repeater light.
    12. Release the two leftmost clips on the cowl screen panel from the LH front fender bracket.
    13. Remove the bolts that attach the upper LH front fender to the vehicle.
    14. Remove the bolt that attaches the lower LH front fender to the vehicle.
    15. Remove the bolt that attaches the rear LH front fender to the vehicle.
    16. Remove the bolt and nut that attach the lower LH front fender to the vehicle.
    17. Inspect the area between the upper LH front fender and the vehicle body for foam sealant. If present, carefully cut the sealant with a blade, and then separate the upper fender from the body with a plastic trim tool.
    18. Remove the LH front fender from the vehicle.
    19. Use a flat scraper blade and isopropyl alcohol (IPA) to remove the foam sealant from the LH outer shotgun panel. Any remaining sealant should be flush with the shotgun panel.
    20. Apply primer to the LH outer shotgun panel, completely covering the previous foam application area.

    安装

    Informational PurposesAn informational icon, calling your attention
    TIp
    For instructions on how to align the fender, refer to .
    1. Load urethane into a caulking gun, and then cut an opening that is 3.5 mm wide and 1.5 mm tall.
    2. Apply a dollop of urethane on top of the primed surface of the LH outer shotgun panel.
    3. Position the LH front fender on the vehicle.
    4. Install the bolt and nut that attach the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
      9.8 Nm (7.2 lbs-ft)
    5. Install the bolt that attaches the rear LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    6. Install the bolt that attaches the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    7. Install the bolts that attach the upper LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    8. Install the cowl screen panel clips (2x) on the LH front fender bracket.
    9. Connect the electrical connectors (2x) to the front side repeater light.
    10. Install the LH headlight. See .
    11. Install the front fascia. See 饰板 - 前（拆卸和安装）.
    12. Install the front aero shield panel. See 面板 - 流线型护板 - 前（拆卸和更换）.
    13. Install the front wheels. See 轮毂总成（拆卸和安装）.
    14. Install the LH shock tower cover. See 盖板 - 减震塔 - 左侧（拆卸和更换）.
    15. For China, Japan and Korea only: Install a new motor ID label on the fender.
    16. Install the underhood storage unit. See .
    17. Install the hood latch cover. See 盖板 - 前备箱盖闩锁（拆卸和更换）.
    18. Install the cabin intake duct. See 槽 - 上部 - 驾驶室进气（拆卸和更换）.
    19. Install the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
    20. Remove the vehicle from the lift.