2024-07-17

轮罩总成(截至 2014 年 11 月 5 日制造)

Repair Information

Parts List

Quantity Description Image / Notes
1 ASSY - RR WHEELEFT HANDOUSE(轮罩总成)
5 Structural Rivet, 6.5 mm Medium
6 Structural Flange Rivet
6 High Strength Structural Rivet, 6.5 mm
4 Structural Bulb Rivet, 6.5 mm
9 SPR,5x4.5
2 SPR,5x6 H2
8 Bolt, hex-head M8-1.25x16 Tesla 零件号 1005582-00-A。
8 Nut HF M8X1.25 10-ZNAL-W Tesla 零件号 2007088。

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆下车身侧外件的必要部分,露出要更换的底层组件。
  2. 拆下前减震塔加固件(如有)。
    Informational PurposesAn informational icon, calling your attention
    2014 年 11 月 5 日前制造的车辆可能配有前减震塔加固件(红色突出显示),必须将其拆下;更换期间无需重新安装此加固件。
  3. Remove the original component.
    or Factory Spot Welds

    or Factory SPRs

    or Factory Structural Rivets

    Factory Pin and Collar

    GMA Weld

  4. 将 C 柱加固件固定到减震塔。
  5. 检查新轮罩加长板组件的配合情况。
    需要时:
    • 根据需要修剪组件的内侧边缘以进行安装。
    • 对后轮罩加长板的弯曲部分进行加热并使其平滑,以便安装后节点(为便于查看,后轮罩加长板在图中单独显示)。
  6. Prepare for installation.
    or Structural Rivets, 6.5 mm Medium

    or Structural Flange Rivets, 6.5 mm

    or Structural Bulb Rivets, 6.5 mm

    or SPRs, 5x4.5
    Informational PurposesAn informational icon, calling your attention
    以下 Tesla SPR 模具用于安装此 SPR:KA 075 2113
    or SPRs, 5x6 H2
    Informational PurposesAn informational icon, calling your attention
    以下 Tesla SPR 模具用于安装此 SPR:SM 085 0125

    or Bolts, hex-head

    Nut

    GMA Weld

  7. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  8. Install the new component or components.
    将这些螺栓拧紧至 25 Nm。
  9. Perform GMA welding.
    GMA Weld
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  10. 安装先前为更换组件而从 车身侧外件 拆下的部分。
  11. Perform any necessary post-repair operations.