2024-07-17

门槛(前部)

Parts List

Quantity Description Image / Notes
1 FRONT SILL SECTION KIT(门槛 - 前部区块套件)
前部门槛完整区块
上部外壳的下部衬垫板
上部外壳的上部衬垫板
下部外壳衬垫板
中部外壳衬垫板
16 Structural Countersunk Rivet, 6.5 mm
11 Structural Bulb Rivet, 6.5 mm
3 Structural Rivet, 6.5 mm Medium
3 拉钉,4.8 毫米
9 防松螺母,M6 - 1.00x3
2 防松螺母,M8 - 1.25x3

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆下铰链柱总成的必要部分。
  2. 拆卸车架前纵梁外延加固件
  3. 拆卸扭矩盒板
  4. 拆下门槛螺母条。
    or Factory Structural Rivets
  5. 拆卸门槛插件。
    or Factory Structural Rivets

    Rivnut

  6. Remove the original component.

    Cut Line

    Reference Line/Point

    • A = 228 毫米。
    • B = 214 毫米。

    Rivnut

    GMA Weld
    Informational PurposesAn informational icon, calling your attention
    部分车辆可能有额外的焊缝,根据需要去除焊缝以进行相关区块维修。
  7. 试装新组件,并将其修剪至合适尺寸。
    • C = 190 毫米。
  8. 制作衬垫板并将其安装在替换组件上。
    Informational PurposesAn informational icon, calling your attention
    将提供的衬垫板修剪至 90 毫米。
    or Structural Bulb Rivets, 6.5 mm
  9. Create and install backing plates 车辆上
    Informational PurposesAn informational icon, calling your attention
    将提供的衬垫板修剪至 90 毫米。
    or Structural Bulb Rivets, 6.5 mm

    or Structural Countersunk Rivets, 6.5 mm

  10. Prepare for installation.
  11. 钻出任何被衬垫板堵塞的现有孔。
  12. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  13. Install the new component or components.
  14. Perform GMA welding.
    Informational PurposesAn informational icon, calling your attention
    打磨下凸缘、扭矩盒到门槛接点以及内侧垂直门槛上的焊缝,直至与周围面板齐平。

    GMA Weld

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  15. 安装门槛插件。
  16. 将防松螺母安装到门槛插件和门槛前部区块。
    Rivnut
  17. 安装门槛螺母条。
  18. 安装扭矩盒板
  19. 安装车架前纵梁外延加固件
  20. 安装轮罩加长件
  21. 安装先前为露出更换组件而拆下的铰链柱总成部分。
  22. Perform any necessary post-repair operations.