围板外壳 – 中国充电端口车辆
Repair Information
- 只要使用本文档中 围板外件总成区块说明 部分指定的参考切割线,即可更换围板外壳的下部。
- Review all collision repair general practices and safety documentation and wear the appropriate PPE (Personal Protective Equipment) before beginning this procedure.
- This procedure can be completed without using a frame bench.
Parts List
Quantity | Description | Image / Notes |
---|---|---|
1 | ASSEMBLY - QUARTER OUTER CHINA GB CHARGE PORT (围板外壳 - 中国区带充电端口的车辆) |
![]() |
2 | Instapak(膨胀泡沫套件) | Tesla 零件号 1046403-00-A。 |
1 |
![]() |
|
8 |
![]() |
|
10 |
![]() |
|
32 |
![]() |
|
18 |
![]() |
|
3 |
![]() |
|
1 |
![]() |
|
1 |
![]() |
When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.
围板外壳区块说明
围板外壳分区 | ||
---|---|---|
围板外壳(如下所示)属于单个组件,可整体更换: | ||
或者,也可以不更换整个 C 柱加固件,而是使用本文档所述的切割线,更换围板外壳的下部。 |
||
围板外壳区块 |
围板外壳区块说明 | |
---|---|
下部
注
Create a backing plate
从新组件的剩余部分,按指示对其进行安装。 |
Repair Procedure
- 从维修总成中拆下多余的组件。
- 分开后轮拱法兰。
- Remove the original component.
-
Prepare for installation.
注A red X indicates a location where a factory-installed fastener is not being replaced.
or
High Strength Structural Rivets, 6.5 mm
or
Structural Bulb Rivets, 6.5 mm
or
Countersunk Rivets, 4.8 mm Short
or
Rivets, 4.8 mm
- A = 5 毫米。
- B = 13 毫米。
- Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
- Install the new component or components.
- 折叠轮拱法兰。
-
更换围板外壳的一个区块:
Perform GMA welding.
or
Aluminum Plug Welds
警告Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.警告To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.警告Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.注Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint. -
安装 Instapak。
向围板外壳与 C 柱加固件之间的腔体中安装一个 Instapak。
- Perform any necessary post-repair operations.