2024-07-17

B 柱

Parts List

Quantity Description Image / Notes
1 B-PILLAR COMPLETE(B 柱)
1 ASY, GUSSET RAMP, B PILLAR INR(角撑板斜轨)
2 High Strength Structural Rivet, 6.5 mm
5 Structural Rivet, 6.5 mm Medium
4 Nut , HF M8 PC10 Tesla 零件号 1046842-00-A。
4 WASHER, M8x24, 2MM Tesla 零件号 1106303-00-A。
Informational PurposesAn informational icon, calling your attention
如需将第一代 B 柱更换为第二代,请订购。可以在当地购买。
如果车辆装配了弓形顶:4 Bolt, hex-head Tesla 零件号 1004537-00-A。
如果车辆装配了弓形顶:4 Flow Form Rivet S38

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆下车身侧外件的必要部分,露出要更换的底层组件。
  2. 如果车辆装配了弓形顶: 分离弓形顶。
    or Factory Spot Welds

    or Bolts, hex-head

  3. 分离 B 柱的底座。
    根据车辆生产日期,可以通过两种方式固定。

    GMA Weld

    Nut

  4. Remove the original component.
    or Factory Spot Welds

    or Factory SPRs

    Cut Line
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    切割相关区块时,请勿损坏底层面板。

    Reference Line/Point

    • A = 10 mm
    • B = 160 毫米
    • C = 50 毫米
  5. 按照指示切割并准备新的 B 柱完整件,以制造新组件。
    or Factory Spot Welds

    Cut Line

    Reference Line/Point

    • A = 10 mm
    • C = 50 毫米
    • D = 135 毫米
  6. 将衬垫板固定到车顶纵梁外件面板。

    or Aluminum Plug Welds

  7. 将衬垫板固定到 A 柱侧内面板。

    or Aluminum Plug Welds

  8. Perform GMA welding.

    or Aluminum Plug Welds

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  9. 对于 2016 年 10 月 11 日之前生产的车辆:将角撑板斜轨安装在门槛上。
    请参阅 B 柱角撑板斜轨 维修程序中的安装说明。
  10. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    如果间隙为 2 毫米或更小,则在 B 柱和 B 柱角撑板斜轨之间安装垫圈 (WASHER, M8x24, 2MM)。如果 B 柱与 B 柱角撑板斜轨之间的间隙超过 2 毫米,则中断此程序并联系 Tesla 碰撞维修团队

    or Aluminum Plug Welds

    or High Strength Structural Rivets, 6.5 mm

    • E = 8 毫米
    • F = 20 毫米

    or Structural Rivets, 6.5 mm Medium

    螺母

    GMA Weld

  11. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  12. Install the new component or components.
    将这些螺栓拧紧至 25 Nm。
  13. Perform GMA welding.

    or Aluminum Plug Welds

    GMA Weld

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  14. 安装先前为更换组件而从 车身侧外件 拆下的部分。
  15. 如果车辆装配了弓形顶:固定弓形顶。
    or Flow Form Rivets, S38 Bolt, hex-head

    将这些螺栓拧紧至 10 Nm。

  16. Perform any necessary post-repair operations.