2024-07-17

围板外壳 – 非中国充电端口车辆

Parts List

Quantity Description Image / Notes
1 ASSY - RR QUARTER OTR(围板外壳)
1 High Strength Structural Rivet, 6.5 mm
8 Structural Bulb Rivet, 6.5 mm
10 Rivet, 4.8 mm
32 Countersunk Rivet, 4.8 mm Short
18 Flow Form Rivet S08
3 Flow Form Rivet S18
1 Flow Form Rivet S28
1 Flow Form Rivet S38

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

围板外壳区块说明

围板外壳分区
围板外壳(如下所示)属于单个组件,可整体更换:

或者,也可以不更换围板外壳总成,而是使用本文档所述的切割线,更换围板外壳的下部。

围板外壳区块

 

围板外壳区块说明

下部

Cut Line

Reference Line/Point

  • A = 264 mm.
  • B = 420 mm.
Informational PurposesAn informational icon, calling your attention
Create a backing plate 从新组件的剩余部分,按指示对其进行安装。

GMA Weld

or Aluminum Plug Welds

Repair Procedure

  1. 分开后轮拱法兰。
  2. Remove the original component.
    Informational PurposesAn informational icon, calling your attention
    仅更换后围外壳的一个区块:仅拆下所要拆卸区块的紧固件。

    or Factory Spot Welds

  3. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    A red X indicates a location where a factory-installed fastener is not being replaced.

    or High Strength Structural Rivets, 6.5 mm

    or Structural Bulb Rivets, 6.5 mm

    or Countersunk Rivets, 4.8 mm Short

    or Rivets, 4.8 mm
    • A = 5 毫米。
    • B = 13 毫米。

    or Flow Form Rivets, S08

    or Flow Form Rivets, S18

    or Flow Form Rivets, S28

    or Flow Form Rivets, S38

  4. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  5. Install the new component or components.
  6. 折叠轮拱法兰。
  7. 更换围板外壳的一个区块 Perform GMA welding.
    or Aluminum Plug Welds

    GMA Weld

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  8. Perform any necessary post-repair operations.