2024-07-17
门槛(外部区块)
Repair Information
- 此维修程序可用于维修侧门槛外件任何区域长度不超过 374 毫米的损坏。如果损坏区域长度超过 374 毫米,则不得维修侧门槛外件:请通过 门槛(整体) 程序更换侧门槛。
- 根据该组件的损坏程度,有可能可以对该组件进行维修。请参阅 门槛维修指南 了解更多信息。
- Review all collision repair general practices and safety documentation and wear the appropriate PPE (Personal Protective Equipment) before beginning this procedure.
- This procedure can be completed without using a frame bench.
Parts List
Quantity | Description | Image / Notes |
---|---|---|
1 | ASY SIDE SILL(门槛总成) |
![]() |
1 | MIDDLE CELL BACKING PLATE - 510 MM(中部外壳衬垫板) |
![]() |
1 | LOWER CELL BACKING PLATE(下部外壳衬垫板) |
![]() |
13 |
![]() |
|
58 |
![]() |
|
17 |
![]() |
|
7 |
![]() |
Tesla 零件号 2007016。 |
2 |
![]() |
Tesla 零件号 1014282-00-A。 |
When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.
Repair Procedure
- 拆下车身侧外件的必要部分,露出要更换的底层组件。
- 拆卸门槛插件。
- 拆下原装组件的损坏区域。
- 裁切新的侧门槛总成,以适合维修区域来制作新组件。
- 将新的中部外壳衬垫板和下部外壳衬垫板裁切成比维修区域长 80 毫米的长度,以制作维修区域所需的衬垫板。
-
将衬垫板安装在维修区域。
or
High Strength Structural Rivets, 6.5 mm
or
Structural Countersunk Rivets, 6.5 mm
警告安装衬垫板时,要有足够的空间来安装门槛插件。注根据维修区域的位置,必须拆下千斤顶衬垫的防松螺母才能插入和安装下部衬垫板。注如果已拆下千斤顶衬垫的防松螺母来插入和安装下部衬垫板,则在衬垫板装好后在这些位置安装新的防松螺母。 -
安装门槛插件。
注在定位门槛插件进行安装之前,必须先安装衬垫板。
- Prepare for installation.
- Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
- Install the new component or components.
-
Perform GMA welding.
GMA Weld
注打磨焊缝,直至与面板齐平。警告Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.警告To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.警告Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.注Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint. - Install the fasteners as indicated.
- 安装先前为更换组件而从 车身侧外件 拆下的部分。
- Perform any necessary post-repair operations.