2024-07-17

门槛(整体)

Repair Information

Parts List

Quantity Description Image / Notes
1 ASY SIDE SILL(门槛 – 整体)
1 ASY, GUSSET RAMP
Informational PurposesAn informational icon, calling your attention
此零件仅适用于 2016 年 4 月 10 日制造的车辆。
37 High Strength Structural Rivet, 6.5 mm
7 Structural Bulb Rivet, 6.5 mm
2 Structural Flange Rivet
12 Structural Rivet, 6.5 mm Medium
2 SPAC NUT,M8X2.8-3.5,STL[10] Tesla 零件号 1071915-00-A。
2 Bolt, hex-head HF M8X50 PC109 MAT Tesla 零件号 1046838-00-A。
4 Nut ,M8-1.25,HF,STEEL[10],ZNAL,BLACK Tesla 零件号 1006628-01-A。
Informational PurposesAn informational icon, calling your attention
此零件仅适用于 2016 年 4 月 10 日制造的车辆。

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆下车身侧外件的必要部分,露出要更换的底层组件。
  2. 拆下铰链柱总成的必要部分。
  3. 拆卸轮罩加长件
  4. 拆卸车架前纵梁外延加固件
  5. 拆卸扭矩盒板
  6. 仅适用于截至 2016 年 4 月 10 日制造的车辆:从门槛上分离 B 柱的底部。
    GMA Weld
  7. 仅适用于 2016 年 4 月 10 日后制造的车辆:从角撑板斜轨上分离 B 柱的底部。
  8. Remove the original component.

    or Factory Spot Welds

    or Factory SPRs

    or Drill through factory spot welds
    Informational PurposesAn informational icon, calling your attention
    When drilling out spot welds, use a drill bit that creates a hole correctly sized for the fastener that will replace the spot weld.

    or Factory Structural Rivets

    or Bolts, hex-head

    GMA Weld

  9. Prepare for installation.

    Cut Line

    Reference Line/Point

    • A = 48 毫米。
    • B = 9 毫米。
    • C = 22 毫米。
    • D = 12 毫米。
    or High Strength Structural Rivets, 6.5 mm
    • E = 58 毫米。
    • F = 32 毫米。
    • G = 39 毫米。
    • H = 144 毫米。
    • I = 14 毫米。
    • J = 30 毫米。
    • K = 25毫米。
    • L = 20 毫米。
    • M = 11 毫米。
    • N = 50 毫米。
    • O = 34 毫米。
    • P = 45 毫米。
    • Q = 65 毫米。
    • R = 55 毫米。
    • S = 80 毫米。
    • T = 90 毫米。
    • U = 6 毫米。
    • V = 44 毫米。
    • W = 166 毫米。
    • X = 8 毫米。
    • Y = 62 毫米。
    • Z = 142 毫米。
    • AA = 160 毫米。
    • BB = 185 毫米。
    • CC = 230 毫米。
    • DD = 56 毫米。
    • EE = 70 毫米。
    • FF = 49 毫米。
    • GG = 47 毫米。

    or Structural Bulb Rivets, 6.5 mm

    or Structural Flange Rivets, 6.5 mm

    or Structural Rivets, 6.5 mm Medium

    A GMA Weld

  10. 暂时安放门槛。
  11. 在后节点上红色圆圈指示的位置开 8 毫米的钻孔。
  12. 拆下门槛。
  13. 将门槛上的 8 毫米孔扩大到 11.5 毫米。
  14. 在 SPAC 螺母的背面涂上粘合剂,将其放在门槛中,然后夹紧到位。
  15. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  16. Install the new component or components.
    安装螺栓并将其拧紧至 25 Nm。
  17. 仅适用于 2016 年 4 月 10 日后制造的车辆:将角撑板斜轨安装在门槛上。
    请参阅 B 柱角撑板斜轨 维修程序中的安装说明。
  18. 仅适用于 2016 年 4 月 10 日后制造的车辆:将 B 柱的底部固定到角撑板斜轨上。
    螺母

    将这些螺母拧紧至 25 Nm。

  19. 仅适用于截至 2016 年 4 月 10 日制造的车辆:将 B 柱的底部固定到门槛上。
    GMA Weld
  20. Perform GMA welding.
    or Aluminum Plug Welds

    GMA Weld

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  21. 安装扭矩盒板
  22. 安装车架前纵梁外延加固件
  23. Install the fasteners as indicated.
    or High Strength Structural Rivets, 6.5 mm
    • D = 12 毫米。
    • P = 45 毫米。
    • Q = 65 毫米。
    • S = 80 毫米。
    • T = 90 毫米。
    • U = 6 毫米。
    • V = 44 毫米。
    • W = 166 毫米。
    • X = 8 毫米。
    • Y = 62 毫米。
    • Z = 142 毫米。
    • AA = 160 毫米。
    • BB = 185 毫米。
    • CC = 230 毫米。
    • DD = 56 毫米。
    • EE = 70 毫米。
    • FF = 49 毫米。
    • GG = 47 毫米。
  24. 安装轮罩加长件
  25. 安装先前为露出更换组件而拆下的铰链柱总成部分。
  26. 安装先前为更换组件而从 车身侧外件 拆下的部分。
  27. Perform any necessary post-repair operations.