2024-07-17

后围内侧(区块)– 非中国区带充电端口的车辆

Parts List

Quantity Description Image / Notes
1 ASSY - RR QTR INR + HDWR(后围内侧 – 区块 – 适用于非中国区带充电端口的车辆)
10 Structural Bulb Rivet, 6.5 mm

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆卸/安装 围板外件总成
  2. 拆卸/安装轮罩外件(整体)的必要部分,以露出下方即将更换的组件。
  3. Remove the original component.
    or Factory Spot Welds

    or Factory Structural Rivets

    • A = 105 毫米。
    • B = 115 毫米。
    • C = 50 毫米。
  4. 按下方所示切割新的 ASSY - RR QTR INR + HDWR,以制作新组件。

    Cut Line

    Reference Line/Point

    Informational PurposesAn informational icon, calling your attention
    使用旧零件作为模板,在法兰外 25 毫米处标记一条切割线,与仍留在车辆上的组件形成搭接接头。
    Informational PurposesAn informational icon, calling your attention
    如图所示,切割上部和下部对接接头的切口,并根据需要进行修剪,以获得良好的对接接头。
    • D = 25 毫米。
  5. Prepare for installation.
    or Structural Bulb Rivets, 6.5 mm
    Informational PurposesAn informational icon, calling your attention
    在搭接接头上按 50 毫米间隔安装结构型灯笼铆钉。这些铆钉需要在车辆内部进行安装。

    GMA Weld

  6. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  7. Install the new component or components.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    在车辆内部为搭接接头安装结构型灯笼铆钉。
  8. Perform GMA welding.
    GMA Weld
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  9. 安装先前为露出更换组件而拆下的轮罩外件(整体)的必要部分。
  10. 拆卸/安装 围板外件总成
  11. Perform any necessary post-repair operations.