2026-05-04

Conjunto de la aleta guardabarros - Parte delantera - Lado izquierdo (Desinstalación e instalación)

Código de corrección 10103001 0.96 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana (FRT) para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte para ver prácticas de trabajo seguras.

  • 2026-03-11: Updated photo and location description of rear fender bolt.
This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

Torque Specifications

Table 1. Especificaciones de apriete:
Descripción Valor de apriete Herramientas recomendadas Reutilizar/Sustituir Notas
Pernos que fijan la parte superior de la defensa delantera al vehículo
4 Nm (2.9 lbs-ft)
  • Vaso de 10 mm
 Reutilizar
Perno que fija el revestimiento de la rueda delantera izquierda a la batería de alta tensión
5 Nm (3.7 lbs-ft)
  • Vaso de 10 mm
 Reutilizar
Perno que fija la esquina izquierda de la defensa delantera a la aleta guardabarros
4 Nm (2.9 lbs-ft)
  • Vaso de 10 mm
 Reutilizar
Perno que fija la esquina derecha de la defensa delantera a la aleta guardabarros
4 Nm (2.9 lbs-ft)
  • Vaso de 10 mm
 Reutilizar
Pernos que sujetan el soporte superior de la aleta guardabarros delantera izquierda a la carrocería
9.8 Nm (7.2 lbs-ft)
  • Vaso de 10 mm de cuello largo
 Reutilizar
Perno que sujeta el soporte de la aleta guardabarros delantera izquierda a la carrocería
9.8 Nm (7.2 lbs-ft)
  • Vaso de 10 mm de cuello largo
 Reutilizar
Perno que sujeta el soporte trasero de la aleta guardabarros delantera izquierda a la carrocería
9.8 Nm (7.2 lbs-ft)
  • Vaso de 10 mm de cuello largo
 Reutilizar
Tuercas que sujetan el soporte inferior de la aleta guardabarros delantera izquierda a la carrocería
9.8 Nm (7.2 lbs-ft)
  • Vaso de 10 mm de cuello largo
 Reutilizar

Retirar

  1. Raise and support the vehicle. See .
  2. Open all doors and fully lower all windows.
  3. Remove the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
  4. Remove the underhood storage unit. See Unidad de almacenamiento del vano del motor (Desinstalación y sustitución).
  5. Remove the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  6. Remove the front wheels. See .
  7. Remove the front aero shield panel. See Panel - Deflector aerodinámico - Delantero (Sin paquete estructural)(Desinstalación y sustitución).
  8. Remove the LH front wheel liner. See Revestimiento del paso de la rueda - Parte delantera - Lado izquierdo (Sin paquete estructural)(Desinstalación y sustitución).
  9. Remove the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
    Figure 1. LH shown; RH similar
  10. Remove the RH front fender garnish. See .
  11. Remove the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  12. Remove the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
    Figure 2. LH shown; RH similar
  13. Disconnect the electrical connector from the front fascia in the RH wheel well.
  14. If present, release the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  15. If present, slide the locking tab away from the connector, and then press down on the locking tab to disconnect the connector from the pedestrian warning speaker assembly.
  16. With an assistant, release the LH side of the front fascia, and then carefully pull the fascia up and forward to remove it from the vehicle. Place the fascia on a padded surface.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully release the tabs that attach the lower headlight bracket to the front fascia, otherwise the tabs can be broken.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The corners of the ankle catcher are very sharp and might cause personal injury.

    LH ankle catcher corner shown; RH corner similar

  17. Remove the LH headlight. See .
  18. Remove the LH side repeater light. See .
  19. Remove the LH fascia side to fender bracket. See .
  20. Release the clip that attaches the cowl screen to the LH side of the carrier bracket.
  21. Remove the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  22. Remove the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  23. Remove the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is located outside the upper fender near the door hinge.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  24. Remove the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  25. Remove the LH front fender assembly from the vehicle

Instalar

Informational PurposesAn informational icon, calling your attention
TIp
For instructions on how to align the fender, refer to .
  1. Install the front underhood storage fender clips onto the LH front fender.
  2. Position the LH front fender assembly onto the vehicle
  3. Install the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  4. Install the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is located inside upper fender.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  5. Install the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  6. Install the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Vaso de 10 mm de cuello largo
  7. Install the clip that attaches the cowl screen to the LH side of the carrier bracket.
  8. Install the LH fascia side to fender bracket. See .
  9. Install the LH side repeater light. See .
  10. Install the LH headlight from the vehicle. See .
  11. With an assistant, position the front fascia onto the vehicle. and then fasten the clips (x8).
  12. If present, install the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  13. If present, connect the pedestrian warning speaker electrical connector, and then engage the connector lock.
  14. Connect the electrical connector for the front fascia in the RH wheel well.
  15. Install the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
    Figure 3. LH shown; RH similar
  16. Install the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  17. Install the RH front fender garnish. See .
  18. Install the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
    Figure 4. LH shown; RH similar
  19. Install the LH front wheel liner. See Revestimiento del paso de la rueda - Parte delantera - Lado izquierdo (Sin paquete estructural)(Desinstalación y sustitución).
  20. Install the LH front fender garnish. See .
  21. Install the front aero shield panel. See Panel - Deflector aerodinámico - Delantero (Sin paquete estructural)(Desinstalación y sustitución).
  22. Install the front wheels. See .
  23. Install the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  24. Install the underhood storage unit. See Unidad de almacenamiento del vano del motor (Desinstalación y sustitución).
  25. Install the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
  26. Open all doors and fully lower all windows.
  27. Remove the vehicle from the lift.