2024-07-17

围板内件区块 (LH) – 2017 年 10 月 3 日后制造的中国区车辆

Parts List

Quantity Description Image / Notes
1 MX ASY - REAR QUARTER INNER PNL CHINA(围板内件 – LH – 2017 年 10 月 3 日后制造的中国区车辆)
19 Structural Bulb Rivet, 6.5 mm

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆卸围板外件 – 为中国区制造的车辆
  2. 拆下后轮拱的必要部分。
  3. Remove the original component.
    or Factory Spot Welds
    • A = 5 毫米。
    • B = 30 毫米。
    • C = 15 毫米。
    Informational PurposesAn informational icon, calling your attention
    请勿去除测量用的点焊。相反,在所示点焊的后方切割 15 毫米。

    Cut Line

    Reference Line/Point

  4. 切割新的围板内件维修零件以制作新组件。
    Informational PurposesAn informational icon, calling your attention
    以旧组件的拆下部分为模板,切割出比旧组件的拆下部分大 30 毫米的维修零件。这个额外的 30 毫米零件将与仍在车上的组件形成搭接接头。

    Cut Line

    Reference Line/Point

    • B = 30 毫米。
    Informational PurposesAn informational icon, calling your attention
    在要安装新组件的顶部前部区域,根据需要修剪新组件,以获得良好的对接接头。
  5. Prepare for installation.
    or Structural Bulb Rivets, 6.5 mm
    • A = 5 毫米。
    • C = 15 毫米。
    • D = 40 毫米。
    • E = 94 毫米。

    GMA Weld

  6. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  7. Install the new component or components.
  8. Perform GMA welding.
    GMA Weld
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  9. 安装后轮拱的必要部分。
  10. 安装围板外件 – 为中国区制造的车辆
  11. Perform any necessary post-repair operations.