2024-07-17

围板内件区块 (RH)

Parts List

Quantity Description Image / Notes
1 ASY - REAR QTR INNER PNL RH(围板内件 – RH)
7 SPR,5x4.5
3 SPR,5x7

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆卸
  2. 拆下后轮拱的必要部分。
  3. Remove the original component.
    or Factory Spot Welds

    Cut Line

    Reference Line/Point

    • A = 170 毫米。
    • B = 184 毫米。
    • C = 25 毫米。
    • D = 10 毫米。
    • E = 110 毫米。
  4. 切割新的围板内件维修零件以制作新组件。
    Informational PurposesAn informational icon, calling your attention
    以旧组件的拆下部分为模板,切割下文所述的维修零件,以制作比旧组件的拆下部分更大的维修零件。新组件应沿前接头与面板的其余部分重叠 25 毫米。新组件应沿后接头与面板其余部分重叠 92 毫米。

    Cut Line

    Reference Line/Point

    • C = 25 毫米。
    • F = 181 毫米。
    Informational PurposesAn informational icon, calling your attention
    在要安装新组件的轮拱区域,根据需要修剪新组件,以获得良好的对接接头。
  5. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    A red X indicates a location where a factory-installed fastener is not being replaced.
    or SPRs, 5x4.5
    Informational PurposesAn informational icon, calling your attention
    安装此 SPR 需要使用以下 Tesla SPR 模具:KA 075 2113
    or SPRs, 5x7
    Informational PurposesAn informational icon, calling your attention
    安装红色圈示的 SPR 时需要使用以下 Tesla SPR 模具:SM 085 0125。使用 Tesla SPR 模具 FM 090 2120 安装未以红色圈示的 SPR。

    GMA Weld

  6. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  7. Install the new component or components.
  8. Perform GMA welding.
    GMA Weld
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  9. 安装后轮拱的必要部分。
  10. 安装
  11. Perform any necessary post-repair operations.