2024-10-23

围板外件 – 非中国用车辆

Parts List

Quantity Description Image / Notes
1 ASSEMBLY - REAR QUARTER OUTER COMP(围板外件)
LH:15

RH:12

Rivet, 4.8 mm
16 Structural Bulb Rivet, 6.5 mm
2 Countersunk Rivet, 4.8 mm Short
1 Countersunk Rivet, 4.8 mm Long
20 Flow Form Rivet S08
14 Flow Form Rivet S18
10 Flow Form Rivet S28
4 Flow Form Rivet S38

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the original component.

    or Factory Spot Welds

    or Drill through factory spot welds
    Informational PurposesAn informational icon, calling your attention
    When drilling out spot welds, use a drill bit that creates a hole correctly sized for the fastener that will replace the spot weld.
  2. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    确保在高压电池附近安装紧固件时使用有足够间隙的紧固件安装工具。只有在没有足够的空间来安装紧固件时,才拆下高压电池。
    Informational PurposesAn informational icon, calling your attention
    A red X indicates a location where a factory-installed fastener is not being replaced.

    or Aluminum Plug Welds

    or Rivets, 4.8 mm

    or Structural Bulb Rivets, 6.5 mm

    or Countersunk Rivets, 4.8 mm Short

    or Countersunk Rivets, 4.8 mm Long

    or Flow Form Rivets, S08

    or Flow Form Rivets, S18

    or Flow Form Rivets, S28

    or Flow Form Rivets, S38

  3. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  4. Install the new component or components.
  5. Perform GMA welding.

    or Aluminum Plug Welds

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  6. 用聚氨酯填充围板外件面板和围板外件下部面板(以红色表示)之间的间隙。
  7. 聚氨酯固化后,使用接缝密封剂全面填充接缝。
  8. Perform any necessary post-repair operations.