2025-04-11

完整车架前纵梁

Parts List

Quantity Description Image / Notes
1 ASSEMBLY - FRONT RAIL（完整车架前纵梁）
1 PNL, LONGITUDINAL UPPER（纵向上部件）
42 High Strength Structural Rivet, 6.5 mm
28 Structural Bulb Rivet, 6.5 mm
10 Countersunk Rivet, 4.8 mm Short
3 Countersunk Rivet, 4.8 mm Long
1 Rivet, 4.8 mm
1 Flow Form Rivet S38
4 Bolt ，BLT,M8x16,M6 HF,[10.9],ZnAl,HD,OD14.9 Tesla 零件号 1011818-00-A。
4 Nut ，NUT,M8-1.25,HF,Steel[10],ZnAl,BLACK Tesla 零件号 1006628-01-A。

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. 拆卸前排座位外侧。
  2. 拆卸前围板横梁。
  3. 拆卸前副框架支架。
  4. Remove the original component.
    or Factory Spot Welds
    or Drill through factory spot welds
    Informational PurposesAn informational icon, calling your attention
    注
    When drilling out spot welds, use a drill bit that creates a hole correctly sized for the fastener that will replace the spot weld.
  5. 做好准备工作，以便在车架前纵梁维修零件上安装纵向上部件。
    or High Strength Structural Rivets, 6.5 mm
    • A = 73 mm
    • B = 63 毫米

    or Rivets, 4.8 mm

    or Installation Spot Welds

  6. 在车架前纵梁维修零件和纵向上部件上涂抹结构型粘合剂。
  7. 在车架前纵梁维修零件上安装纵向上部件。
  8. Perform resistance spot welding.
    or Installation Spot Welds
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
  9. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    注
    A red X indicates a location where a factory-installed fastener is not being replaced.

    or High Strength Structural Rivets, 6.5 mm

    or Structural Bulb Rivets, 6.5 mm

    or Countersunk Rivets, 4.8 mm Short
    Informational PurposesAn informational icon, calling your attention
    注
    某些铆钉的安装位置与部分工厂点焊焊缝位置存在偏移。

    or Countersunk Rivets, 4.8 mm Long

    or Flow Form Rivets, S38

    or Bolts
    • C = 10 毫米
    • D = 9 毫米

    Nut

  10. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  11. Install the new component or components.
    将螺栓拧紧至 22 Nm。
  12. 拆卸/安装 前副框架支架。
  13. 安装前围板横梁。
  14. 安装前排座位外侧。
  15. 如图所示安装丁基补片。
  16. Perform any necessary post-repair operations.