2024-12-17

副框架连接盖

Parts List

Quantity Description Image / Notes
1 BRACKET - SUBFRAME CAP ATTACHMENT（前副框架连接盖）
1 COLLAR - SUBFRAME FRONT（前副框架连接环）
7 High Strength Structural Rivet, 6.5 mm
1 Bolt , HF,M12-1.75X99,[109],ZNFL,CMAT Tesla 零件号 1461643-00-A。
When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the original component.

    or Factory Spot Welds

    GMA Weld

  2. 研磨 COLLAR - SUBFRAME FRONT（以红色突出显示）的凸起部分，以形成平坦的接合面。
  3. 在 FRONT SUBFRAME SUPPORT PANEL 上切一个开口，以便进行 GMA 焊接。
    Reference Line/Point
    • A = 56 毫米
    • B = 24 毫米
    • C = 24 毫米
    • D = 5 毫米

    Cut Line

  4. Prepare for installation.
    or High Strength Structural Rivets, 6.5 mm
    or Steel Plug Welds
    Informational PurposesAn informational icon, calling your attention
    注
    为每个钢塞焊焊缝钻一个 11 毫米的孔。
    or Bolts
    Informational PurposesAn informational icon, calling your attention
    注
    使用螺栓和车架工作台装置定位 BRACKET - SUBFRAME CAP ATTACHMENT 和 COLLAR - SUBFRAME FRONT，以进行 GMA 焊接。

    GMA Weld

  5. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
    Informational PurposesAn informational icon, calling your attention
    注
    请勿将结构型粘合剂涂抹在 COLLAR - SUBFRAME FRONT 和 BRACKET - SUBFRAME CAP ATTACHMENT 之间的接合面上。
  6. Install the new component or components.
    将螺栓拧紧至 10 Nm。
    Informational PurposesAn informational icon, calling your attention
    注
    在进行 GMA 焊接前，拧紧螺栓以使 COLLAR - SUBFRAME FRONT 完全固定在 BRACKET - SUBFRAME CAP ATTACHMENT 上。
  7. Perform GMA welding.
    GMA Weld

    or Steel Plug Welds

    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to 已批准的气体保护金属极弧 (GMA) 焊接器和焊丝 for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    注
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
    Informational PurposesAn informational icon, calling your attention
    注
    GMA 焊接完成后，拆卸并弃置固定 COLLAR - SUBFRAME FRONT 和 BRACKET - SUBFRAME CAP ATTACHMENT 的螺栓。
  8. Perform any necessary post-repair operations.