2026-10-15

气囊 - 帘式 - 左侧（拆卸和更换）

校正代码 20012002 1.62 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure. NOTE: See for safe and healthy working practices.

  • 2026-02-20: 添加了“如需通过本程序诊断辅助约束系统 (SRS) ，请使用 PROC_RCM_DISARM”的说明。
  • 2024 年 2 月 5 日：添加了“气帘紧固件数量不同”的说明。
警告
Supplemental Restraint System (SRS) components can be hazardous if not serviced and handled correctly. See
警告
In the event of an airbag or seatbelt pretensioner deployment, certain components must be replaced, and other components must be inspected for damage. Refer to the Collision Repair Manual for a specific list of items that must be inspected and replaced.
警告
If using this procedure to diagnosis the vehicle's Supplemental Restraint Systems (SRS), disarm the RCM, which will prevent all airbags and pretensioners from deploying. Re-arm the RCM after all of the vehicle's SRS components are re-installed.
  • Disarm RCM:PROC_RCM_DISARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Disarm RCM
    • Safety & Restraints ➜ Seats ➜ Disarm RCM
    via Toolbox:(link)
  • Re-arm RCM:PROC_RCM_ARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Re-Arm RCM
    • Safety & Restraints ➜ Seats ➜ Re-Arm RCM
    via Toolbox:(link)
警告
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Disconnect the 12V/LV battery and the First Responder Loop. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see .

扭矩规格

表 1. 扭矩规格： 气囊 - 帘式 - 左侧（拆卸和更换）
描述 扭矩值 推荐工具 重复使用/更换 备注
将左侧帘式气囊固定到车身的螺栓
9 Nm (6.6 lbs-ft)
  • 10 毫米套筒扳手
 重复使用

拆卸

  1. 打开所有车门，完全降下所有车窗。
  2. 打开掀背尾门。
  3. 拆下前部顶篷。请参阅 。
  4. 拆下后部顶篷。请参阅 顶篷 - 后（拆卸和更换）。
  5. 拆下第二排座椅下部座垫。请参阅 座椅座垫 - 下部 - 第二排（拆卸和更换）。
  6. 断开 12V 电源。请参阅 12V/低压电源（断开和连接）。
  7. 断开左侧帘式气囊连接器上的电气线束。
  8. 拆下将左侧帘式气囊的前部和中部固定到车身的螺栓。
    注
    The number of fasteners varies depending on vehicle build date/airbag revision.
    提示
    推荐使用以下工具
    • 10 毫米套筒扳手
  9. 拆下将左侧帘式气囊的后部固定到车身的螺栓。
    注
    The number of fasteners varies depending on vehicle build date/airbag revision.
    提示
    推荐使用以下工具
    • 10 毫米套筒扳手
  10. 小心地松开将左侧帘式气囊固定到纵梁的夹子 (x8)，然后从车上拆下气囊。
    警告
    如有任何卡子发生损坏，请更换气囊。
    警告
    气囊始终应由点火器操控；切勿让点火器处于悬垂状态。
    注
    The number of fasteners varies depending on vehicle build date/airbag revision.

安装

  1. 将左侧帘式气囊安装到纵梁上，然后小心地紧固将气囊固定到纵梁的夹子 (x8)。
    警告
    如有任何卡子发生损坏，请更换气囊。
    注
    The number of fasteners varies depending on vehicle build date/airbag revision.
  2. 安装并用手拧紧将左侧帘式气囊的后部固定到车身的螺栓。
    注
    The number of fasteners varies depending on vehicle build date/airbag revision.
  3. 安装并用手拧紧将左侧帘式气囊的前部和中部固定到车身的螺栓。
    注
    The number of fasteners varies depending on vehicle build date/airbag revision.
  4. 紧固将左侧帘式气囊固定到车身的螺栓。
    9 Nm (6.6 lbs-ft)
    提示
    推荐使用以下工具
    • 10 毫米套筒扳手
  5. 将电气线束与左侧帘式气囊连接器相连。
  6. 安装后部顶篷。请参阅 顶篷 - 后（拆卸和更换）。
  7. 安装前部顶篷。请参阅 。
  8. 连接 12V 电源。请参阅 12V/低压电源（断开和连接）。
  9. 安装第二排座椅下部座垫。请参阅 座椅座垫 - 下部 - 第二排（拆卸和更换）。