2026-06-23

Rear Quarter Outer Skin With C-Pillar Lower Extension (Vehicles Built After February 14, 2022)

Correction code: 10100136202 10100136302 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair and Service repair work required to perform this procedure, including the linked Collision Repair procedures and linked Service procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Depending on the damage to the vehicle, additional repairs may be required.

Parts List

Quantity Description Image / Notes
1 REAR QUARTER OUTER COMPLETE (Rear Quarter Complete)
12 Structural Bulb Rivet, 6.5 mm
21 Countersunk Rivet, 4.8 mm Short
1 Countersunk Rivet, 4.8 mm Long
8 Flow Form Rivet S08
15 Flow Form Rivet S18
7 Flow Form Rivet S28
3 Flow Form Rivet S38

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the Racetrack Trim - Rear - LH (Remove and Replace).
  2. Remove the Trim - Liftgate Trough - LH (Remove and Replace).
  3. Remove the Taillight - LH (Remove and Replace).
  4. Remove the Reflex Marker - Taillight - RH (Global) (Remove and Replace).
  5. Remove the Taillight - RH (Remove and Replace).
  6. Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
  7. Remove the Carrier - Rocker Panel - LH (Remove and Replace).
  8. Remove the Garnish - Fender - Rear - LH (Remove and Replace).
  9. Remove the Glass - Rear Quarter - LH (Remove and Install).
  10. Remove the Trim - Side - Trunk - RH (Remove and Replace).
  11. Remove the Trim - Sill - Trunk (Remove and Replace).
  12. Remove the Trim - Side - Trunk - LH (5 Seat) (Remove and Replace).
  13. Remove the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  14. Remove the Liftgate (Remove and Replace).
  15. Remove the Bracket - Rear Wing - LH (Remove and Replace).
  16. Remove the Air Extractor - Rear - Inner - LH (Remove and Replace).
  17. Remove the Bracket - Racetrack - C-Pillar - Upper - LH (Remove and Replace).
  18. Remove the Bracket - Racetrack - C-Pillar - Lower - LH (Remove and Replace).
  19. Remove the Bracket - Racetrack - Sill - LH (Remove and Replace).
  20. Remove the Racetrack Trim - Rear - LH (Remove and Replace).
  21. Remove the Trim - Liftgate Trough - LH (Remove and Replace).
  22. Remove the Taillight - LH (Remove and Replace).
  23. Remove the Charge Port (NACS) (Remove and Replace).
  24. Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
  25. Remove the Carrier - Rocker Panel - LH (Remove and Replace).
  26. Remove the Garnish - Fender - Rear - LH (Remove and Replace).
  27. Remove the Glass - Rear Quarter - LH (Remove and Install).
  28. Remove the Trim - Side - Trunk - RH (Remove and Replace).
  29. Remove the Trim - Sill - Trunk (Remove and Replace).
  30. Remove the Trim - Side - Trunk - LH (5 Seat) (Remove and Replace).
  31. Remove the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  32. Remove the Liftgate (Remove and Replace).
  33. Remove the Bracket - Rear Wing - LH (Remove and Replace).
  34. Remove the Air Extractor - Rear - Inner - LH (Remove and Replace).
  35. Remove the following components from the service part to make the new component.
  36. Remove the original component.

    or Factory Spot Welds

    or Drill through factory spot welds

    or Factory laser welds
    Informational PurposesAn informational icon, calling your attention
    Note
    Bulk cut remaining quarter to access laser weld in the back.
  37. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    A red X indicates a location where a factory-installed fastener is not being replaced. Secure this location using structural adhesive only.

    or Structural Bulb Rivets, 6.5 mm

    or Countersunk Rivets, 4.8 mm Short

    or Countersunk Rivets, 4.8 mm Long

    or Flow Form Rivets, S08

    or Flow Form Rivets, S18

    or Flow Form Rivets, S28

    or Flow Form Rivets, S38

  38. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  39. Install the new component or components.
  40. Perform any necessary post-repair operations.
  41. Install the Air Extractor - Rear - Inner - LH (Remove and Replace).
  42. Install the Bracket - Rear Wing - LH (Remove and Replace).
  43. Install the Liftgate (Remove and Replace).
  44. Install the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  45. Install the Trim - Side - Trunk - LH (5 Seat) (Remove and Replace).
  46. Install the Trim - Sill - Trunk (Remove and Replace).
  47. Install the Trim - Side - Trunk - RH (Remove and Replace).
  48. Install the Glass - Rear Quarter - LH (Remove and Install).
  49. Install the Garnish - Fender - Rear - LH (Remove and Replace).
  50. Install the Carrier - Rocker Panel - LH (Remove and Replace).
  51. Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
  52. Install the Charge Port (NACS) (Remove and Replace).
  53. Install the Taillight - LH (Remove and Replace).
  54. Install the Trim - Liftgate Trough - LH (Remove and Replace).
  55. Install the Racetrack Trim - Rear - LH (Remove and Replace).
  56. Install the Bracket - Racetrack - Sill - LH (Remove and Replace).
  57. Install the Bracket - Racetrack - C-Pillar - Lower - LH (Remove and Replace).
  58. Install the Bracket - Racetrack - C-Pillar - Upper - LH (Remove and Replace).
  59. Install the Air Extractor - Rear - Inner - LH (Remove and Replace).
  60. Install the Bracket - Rear Wing - LH (Remove and Replace).
  61. Install the Liftgate (Remove and Replace).
  62. Install the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  63. Install the Trim - Side - Trunk - LH (5 Seat) (Remove and Replace).
  64. Install the Trim - Sill - Trunk (Remove and Replace).
  65. Install the Trim - Side - Trunk - RH (Remove and Replace).
  66. Install the Glass - Rear Quarter - LH (Remove and Install).
  67. Install the Garnish - Fender - Rear - LH (Remove and Replace).
  68. Install the Carrier - Rocker Panel - LH (Remove and Replace).
  69. Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
  70. Install the Taillight - RH (Remove and Replace).
  71. Install the Reflex Marker - Taillight - RH (Global) (Remove and Replace).
  72. Install the Taillight - LH (Remove and Replace).
  73. Install the Trim - Liftgate Trough - LH (Remove and Replace).
  74. Install the Racetrack Trim - Rear - LH (Remove and Replace).