2026-06-23

Rear Quarter Outer (Complete) (Vehicles Built After February 14, 2022)

Correction code: 10100115302 10100115502 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair and Service repair work required to perform this procedure, including the linked Collision Repair procedures and linked Service procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Depending on the damage to the vehicle, additional repairs may be required.

Parts List

Quantity Description Image / Notes
1 REAR QUARTER OUTER COMPLETE (Rear Quarter Outer Complete)
LH component: 11

RH component: 12

 Rivet, 4.8 mm
16 Structural Bulb Rivet, 6.5 mm
2 Countersunk Rivet, 4.8 mm Short
1 Countersunk Rivet, 4.8 mm Long
20 Flow Form Rivet S08
14 Flow Form Rivet S18
10 Flow Form Rivet S28
4 Flow Form Rivet S38

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  2. Remove the Bracket - Racetrack - Sill - LH (Remove and Replace).
  3. Remove the Striker - Door - Rear - LH (Remove and Replace).
  4. Remove the Seal - Liftgate (Remove and Replace).
  5. Remove the Carrier - Rocker Panel - LH (Remove and Replace).
  6. Remove the Power Strut - Liftgate (Remove and Replace).
  7. Remove the Assembly - Trailer Hitch (Remove and Replace).
  8. Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
  9. Remove the Insulator - Wheelhouse - Rear - RH (Remove and Replace).
  10. Remove the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  11. Remove the Air Extractor - Rear - Outer - LH (Remove and Replace).
  12. Remove the Reflex Marker - Taillight - RH (Global) (Remove and Replace).
  13. Remove the Taillight - RH (Remove and Replace).
  14. Remove the Door Assembly - Rear Lower - LH (Remove and Replace).
  15. Remove the Glass - Rear Quarter - LH (Remove and Replace).
  16. Remove the Liftgate (Remove and Replace).
  17. Remove the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  18. Remove the Bracket - Racetrack - Sill - LH (Remove and Replace).
  19. Remove the Striker - Door - Rear - LH (Remove and Replace).
  20. Remove the Seal - Liftgate (Remove and Replace).
  21. Remove the Carrier - Rocker Panel - LH (Remove and Replace).
  22. Remove the Power Strut - Liftgate (Remove and Replace).
  23. Remove the Assembly - Trailer Hitch (Remove and Replace).
  24. Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
  25. Remove the Duct - Busbar - 3rd Row - LH (Remove and Replace).
  26. Remove the Insulator - Wheelhouse - Rear - LH (Remove and Replace).
  27. Remove the Bracket - Rear Wing - LH (Remove and Replace).
  28. Remove the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  29. Remove the Air Extractor - Rear - Outer - LH (Remove and Replace).
  30. Remove the Taillight - LH (Global) (Remove and Replace).
  31. Remove the Glass - Rear Quarter - LH (Remove and Replace).
  32. Remove the Door Assembly - Rear Lower - LH (Remove and Replace).
  33. Remove the Liftgate (Remove and Replace).
  34. Remove the original component.

    or Factory Spot Welds

    or Drill through factory spot welds

  35. Prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    A red X indicates a location where a factory-installed fastener is not being replaced. Secure this location using structural adhesive only.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make certain to use fastener installation tools that have adequate clearance when when installing fasteners near the HV Battery. Remove the HV Battery only if there is not sufficient space to install fasteners.

    or Aluminum Plug Welds

    or Rivets, 4.8 mm

    or Structural Bulb Rivets, 6.5 mm

    or Countersunk Rivets, 4.8 mm Short

    or Countersunk Rivets, 4.8 mm Long

    or Flow Form Rivets, S08

    or Flow Form Rivets, S18

    or Flow Form Rivets, S28

    or Flow Form Rivets, S38

  36. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  37. Install the new component or components.
  38. Perform GMA welding.

    or Aluminum Plug Welds

    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to Approved Gas Metal Arc (GMA) Welders and Welding Wire for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Note
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  39. Perform any necessary post-repair operations.
  40. Install the Liftgate (Remove and Replace).
  41. Install the Door Assembly - Rear Lower - LH (Remove and Replace).
  42. Install the Glass - Rear Quarter - LH (Remove and Replace).
  43. Install the Taillight - LH (Global) (Remove and Replace).
  44. Install the Air Extractor - Rear - Outer - LH (Remove and Replace).
  45. Install the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  46. Install the Bracket - Rear Wing - LH (Remove and Replace).
  47. Install the Insulator - Wheelhouse - Rear - LH (Remove and Replace).
  48. Install the Duct - Busbar - 3rd Row - LH (Remove and Replace).
  49. Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
  50. Install the Assembly - Trailer Hitch (Remove and Replace).
  51. Install the Power Strut - Liftgate (Remove and Replace).
  52. Install the Carrier - Rocker Panel - LH (Remove and Replace).
  53. Install the Seal - Liftgate (Remove and Replace).
  54. Install the Striker - Door - Rear - LH (Remove and Replace).
  55. Install the Bracket - Racetrack - Sill - LH (Remove and Replace).
  56. Install the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  57. Install the Liftgate (Remove and Replace).
  58. Install the Glass - Rear Quarter - LH (Remove and Replace).
  59. Install the Door Assembly - Rear Lower - LH (Remove and Replace).
  60. Install the Taillight - RH (Remove and Replace).
  61. Install the Reflex Marker - Taillight - RH (Global) (Remove and Replace).
  62. Install the Air Extractor - Rear - Outer - LH (Remove and Replace).
  63. Install the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  64. Install the Insulator - Wheelhouse - Rear - RH (Remove and Replace).
  65. Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
  66. Install the Assembly - Trailer Hitch (Remove and Replace).
  67. Install the Power Strut - Liftgate (Remove and Replace).
  68. Install the Carrier - Rocker Panel - LH (Remove and Replace).
  69. Install the Seal - Liftgate (Remove and Replace).
  70. Install the Striker - Door - Rear - LH (Remove and Replace).
  71. Install the Bracket - Racetrack - Sill - LH (Remove and Replace).
  72. Install the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).