2026-06-23

Rear Node (Complete) (Vehicles Built From January 1, 2021 Through March 6, 2022)

Correction code: 10101820502 10101820402 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair and Service repair work required to perform this procedure, including the linked Collision Repair procedures and linked Service procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Depending on the damage to the vehicle, additional repairs may be required.

Parts List

Quantity Description Image / Notes
1 ASY-MEMBER RAIL RR (Rear Node – Complete)
LH: 23

RH: 22

 High Strength Structural Rivet, 6.5 mm
6 Structural Countersunk Rivet, 6.5 mm
1 Bolt , M8x20 Tesla part number 1007580-00-A.
1 Bolt , M8x50 Tesla part number 1046838-00-A.
1 Bolt , M8x27 Tesla part number 1621820-00-A.
1 Bolt , HF, M8-1.25x22,[109],G0110,MAT Tesla part number 1552447-00-A.
2 Bolt, Torx-head , M8x20 Tesla part number 1014747-00-B.
2 Nut , M8-1.25,HF,Steel[10],ZnAl,BLACK Tesla part number 1006628-01-A.

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the Busbars - Charge Port to HV Battery (Remove and Replace).
  2. Remove the Seat Assembly - 2nd Row - LH (7 Seat) (Remove and Replace).
  3. Remove the Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace).
  4. Remove the Panel - Aero Shield - Front (Remove and Replace).
  5. Remove the Brake Lines - Rear - LH to Sill (Remove and Replace).
  6. Remove the Noise Absorber - Motor Bay - Rear (Remove and Replace).
  7. Remove the Active Damper - Rear - LH (Remove and Replace).
  8. Remove the NVH Insulator - Floor - 3rd Row (Remove and Replace).
  9. Remove the Insulator - Wheelhouse - Rear - LH (Remove and Replace).
  10. Remove the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  11. Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
  12. Remove the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  13. Remove the Seat Assembly - 2nd Row - LH (7 Seat) (Remove and Replace).
  14. Remove the Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace).
  15. Remove the Panel - Aero Shield - Front (Remove and Replace).
  16. Remove the Brake Lines - Rear - RH to Sill (Remove and Replace).
  17. Remove the Noise Absorber - Motor Bay - Rear (Remove and Replace).
  18. Remove the Active Damper - Rear - LH (Remove and Replace).
  19. Remove the NVH Insulator - Floor - 3rd Row (Remove and Replace).
  20. Remove the Insulator - Wheelhouse - Rear - RH (Remove and Replace).
  21. Remove the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  22. Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
  23. Remove the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  24. Remove the Second Row Seat Floor Panel.
  25. Remove the Rear Panel.
    Based on the vehicle build date, remove the Rear Panel using the appropriate procedure:
  26. Remove the Rear Trunk Floor.
    Based on the vehicle build date, remove the Rear Trunk Floor using the appropriate procedure:
  27. Remove the Rear Trunk Waterfall Panel.
    Based on the vehicle build date, remove the Rear Trunk Waterfall Panel using the appropriate procedure:
  28. Remove the Rear Node Upper Reinforcement (Front).
  29. Remove the Rear Node Upper Reinforcement (Rear).
  30. Remove the Rear Torque Box Lower Reinforcement.
  31. Remove the Rear Trunk Floor Panel Extension.
  32. Remove the Rear Node Outer Reinforcement.
  33. Remove the Rear Shock Tower Reinforcement.
  34. Remove the original component.

    or Factory Spot Welds

    or RIVTAC

    or Factory Structural Rivets

    or Bolts

    or Bolt, Torx-head

    Factory BOM

  35. Use structural adhesive to attach the nuts in position on the inside of the Rear Node.
    Informational PurposesAn informational icon, calling your attention
    Note
    If necessary, grind the edges of the nuts to make them flush with the mounting location.

    Nut

  36. Prepare for installation.
    or High Strength Structural Rivets, 6.5 mm
    • A = 260 mm.
    • B = 15 mm.
    • C = 24 mm.
    • D = 9 mm.
    • E = 12 mm.
    • F = 11 mm.

    or Structural Countersunk Rivets, 6.5 mm

    or Bolts

    or Bolt, Torx-head

  37. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  38. Install the new component or components.

    Torque the bolts as follows:

    • Hex-head M8x27 bolts part number 1621820-00-A: 24 Nm.
    • Hex-head M8x50 bolts part number 1046838-00-A: 24 Nm.
    • Hex-head M8x20 bolts part number 1007580-00-A: 25 Nm.
    • Torx bolts (all): 24 Nm.
  39. Install the Rear Node Upper Reinforcement (Front).
  40. Install the Rear Node Upper Reinforcement (Rear).
  41. Install the Rear Torque Box Lower Reinforcement.
  42. Install the Rear Trunk Waterfall Panel.
    Install the Rear Trunk Waterfall Panel using the appropriate procedure:
  43. Install the Rear Trunk Floor.
    Install the Rear Trunk Floor using the appropriate procedure:
  44. Install the Rear Trunk Floor Panel Extension.
  45. Install the Rear Node Outer Reinforcement.
  46. Install the Rear Shock Tower Reinforcement.
  47. Install the Rear Panel.
    Install the Rear Panel using the appropriate procedure:
  48. Install the Second Row Seat Floor Panel.
  49. Perform any necessary post-repair operations.
  50. Install the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  51. Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
  52. Install the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  53. Install the Insulator - Wheelhouse - Rear - RH (Remove and Replace).
  54. Install the NVH Insulator - Floor - 3rd Row (Remove and Replace).
  55. Install the Active Damper - Rear - LH (Remove and Replace).
  56. Install the Noise Absorber - Motor Bay - Rear (Remove and Replace).
  57. Install the Brake Lines - Rear - RH to Sill (Remove and Replace).
  58. Install the Panel - Aero Shield - Front (Remove and Replace).
  59. Install the Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace).
  60. Install the Seat Assembly - 2nd Row - LH (7 Seat) (Remove and Replace).
  61. Install the Bracket - Attachment - Fascia - Rear (Remove and Replace).
  62. Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
  63. Install the Seal - Body - Side - Rear - Primary - LH (Remove and Replace).
  64. Install the Insulator - Wheelhouse - Rear - LH (Remove and Replace).
  65. Install the NVH Insulator - Floor - 3rd Row (Remove and Replace).
  66. Install the Active Damper - Rear - LH (Remove and Replace).
  67. Install the Noise Absorber - Motor Bay - Rear (Remove and Replace).
  68. Install the Brake Lines - Rear - LH to Sill (Remove and Replace).
  69. Install the Panel - Aero Shield - Front (Remove and Replace).
  70. Install the Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace).
  71. Install the Seat Assembly - 2nd Row - LH (7 Seat) (Remove and Replace).
  72. Install the Busbars - Charge Port to HV Battery (Remove and Replace).